PerkinElmer Lambda 650 Скачать руководство пользователя страница 6

Страница: 6 / 72

6 . Introduction

Overview

This hardware guide covers the operating instructions for the Lambda 650, Lambda 850 and

Lambda 950 instruments plus those maintenance routines that do not necessarily require a

PerkinElmer Service Engineer.

NOTE:

Responsible Body: Individual or body responsible for the use and maintenance of equipment

and for ensuring that OPERATORS are adequately trained.

There are separate manuals for the Sphere and Universal Reflectance accessories which can
be found on the Lambda 650/850/950 Manuals CD.

This manual is divided into following chapters:

Chapter 1 Introduction

This chapter contains a brief introduction on the instrument, the conventions and warnings

used in the manual.

Chapter 2 Safety Practices

Important safety information is provided in this chapter. It is the same information as given

in the Lambda 650/850/950 Getting Started Guide that shipped with your instrument.

Chapter 4 System Description

This chapter contains information on the components of the instrument, how it works and
instrument specifications.

Chapter 5 Lambda 650 Installation

Information on installing Lambda 650 instrument. Only the 650 should be customer

installed, the 850 and 950 instruments should be installed a PerkinElmer Service

representative. This is the same information given in the Lambda 650/850/950 Getting
Started Guide that shipped with your instrument.

Chapter 6 Using the Instrument

Startup procedure and general instructions for using the instrument are provided.

Chapter 7 Maintenance

Maintenance and cleaning procedures for the various components of your instrument are

provided.

Содержание Lambda 650









































































Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Lambda 650, Руководство по оборудованию

Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды