PerkinElmer Lambda 650 Скачать руководство пользователя страница 62

Страница: 62 / 72

62 . Maintenance

Figure 21 Removing the halogen lamp connector

Remove the halogen lamp assembly from the bracket by slackening the thumbscrew
and pulling the lamp mount vertically upward.
Save the thumbscrew for use with the new lamp assembly.

Unpack the new lamp assembly, taking care to hold it only by the metal mount to

prevent finger marks on the bulb.

Slip the slot at the base of the lamp mount over the stud on the bracket in the lamp

compartment and then secure with the thumbscrew.

Carefully push the halogen lamp connector firmly onto the pins on the base of the

halogen lamp.

Wipe the halogen lamp bulb with a soft cloth moistened with alcohol to remove dirt,

since this would otherwise be burned in when the lamp is hot.

10.

Replace the lamp compartment cover by lowering it into position.
This completes the halogen lamp replacement procedure.

NOTE:

Due to the pre-aligned mounts, the alignment of lamps after installation is generally so good

that further alignment is not required.

Deuterium Lamp Replacement

If the lamp burns out, or indicates falling energy after prolonged use, you should replace the

lamp. Replacement lamp assemblies (B0160917) are provided complete with pre-aligned

mounts.

Figure 22 Pre-aligned Deuterium Lamp Assembly (B0160917)

Thumbscrew (halogen lamp)

Halogen lamp
connector

Operating Hours Counter

Halogen lamp
assembly

Содержание Lambda 650









































































Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Lambda 650, Руководство по оборудованию

Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды