manualshive.com logo in svg

PerkinElmer Lambda 650, Руководство по оборудованию

Поделиться
Скачать
PerkinElmer Lambda 650 Скачать руководство пользователя страница 56

56 . Maintenance 

 

Overview 

 

 

WARNING 

Unauthorized Adjustments and Servicing 

Do not attempt to make adjustments, replacements or repairs to this 

instrument except as described here. Only a PerkinElmer service 

representative or similarly trained and authorized person should be 

permitted to service the instrument. Please contact your local 

PerkinElmer sales or service office. 

This chapter describes the routine maintenance procedures required to keep your instrument 

in proper working condition and to ensure the highest possible level of performance. It 

includes maintenance checks that should be done on a daily basis and maintenance 

procedures that should be done periodically depending on instrument use. This chapter is 

divided into several sections, each section covering maintenance procedures for a particular 
component of the system. 

You should perform only the maintenance procedures described in this chapter. If additional 

maintenance is required, contact a PerkinElmer Service Engineer. 

 

CAUTION 

Before using any cleaning or decontamination methods except those 

specified here, users should check with PerkinElmer that the proposed 

method will not damage the equipment. 

 

 

Содержание Lambda 650









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды