PerkinElmer Lambda 650 Скачать руководство пользователя страница 25

Страница: 25 / 72

Lambda 650/850/950 Hardware Guide . 25

Optical System

The Lambda 650/850/950 Spectrometer features an all-reflecting, double-monochromator

optical system. The optical components are coated with silica for durability. Holographic

gratings are used in each monochromator for the UV/Vis range and the NIR range.

The optical system is depicted schematically in Figure 7.

Figure 7 Schematic of Optical System

Two radiation sources, a deuterium lamp (DL) and a halogen lamp (HL), cover the working
wavelength range of the spectrometer.

For operation in the near infrared (NIR) and visible (Vis) ranges, source mirror M1 reflects

the radiation from the halogen lamp onto mirror M2. At the same time it blocks the radiation

from the deuterium lamp.

SBA

Detector

Compartment

M11

(below PbS)

Sample

Compartment

M13

CBM

M10

RBA

Monochromator I

NIR

Monochromator II

UV/Vis

NIR

UV/Vis

M12

M13

M14

PbS

Содержание Lambda 650









































































Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Lambda 650, Руководство по оборудованию

Результаты поиска

Содержание Lambda 650

Отзывы:

Бренды по названию

Популярные бренды