Paradyne Hotwire 8799 Скачать руководство пользователя

Страница: 47 / 154

4. Monitoring the Card

8799-A2-GB20-10

April 2003

4-11

Viewing DSL Performance Statistics

DSL performance statistics allow you to monitor the current status of DSL
operations.

To view DSL Performance Statistics for a port, follow this menu selection
sequence:

Main Menu

→

Status

→

Performance Statistics

→

DSL Performance Statistics

The following DSL Performance Statistics are collected for the selected port:

MrGn:

The margin level calculated from the Signal to Noise Ratio (SNR)

measured minus the SNR reference. The SNR reference is the value needed
to maintain a bit error rate of 10

-6

XmtPw:

The transmit power level in dBm.

Atten:

The number of dB that the signal is below a reference point.

main/status/performance/dsl_perf

Slot: 4: Model: 8799

Port: 3 DSL PERFORMANCE STATISTICS

Payload Rate: 1536 kbps

Current Interval Timer: 002 DSL Line Rate: 1544 kbps

--------------------------------------------------------------------------------

--MrGn-- --XmtPw- --Atten-

Near Far Near Far Near Far

Current Int: +02 +01 +03 +02 +02

Interval 01 +02 +03 +03 +02 +02

Interval 02 +02 +01 +03 +02 +02

Interval 03 +02 +01 +03 +02 +02

Interval 04 +02 +01 +03 +02 +02

Interval 05 +02 +01 +03 +02 +02

Interval 06 +02 +01 +03 +02 +02

Interval 07 +02 +01 +03 +02 +02

--------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu MainMenu Exit

PgUp PgDn

Select 1, 2, 3, 4 ,5, 6, 7, 8. LOS at DSL Pt 2

Содержание Hotwire 8799



























































































































































Результаты поиска

Содержание Hotwire 8799

Отзывы:

Похожие инструкции для Hotwire 8799

Бренды по названию

Популярные бренды

Paradyne Hotwire 8799, Руководство пользователя

Результаты поиска

Содержание Hotwire 8799

Отзывы:

Похожие инструкции для Hotwire 8799

Бренды по названию

Популярные бренды