Paradyne Hotwire 8799 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 154

Paradyne Hotwire 8799 Скачать руководство пользователя страница 35

3. Initial Startup and Configuration

8799-A2-GB20-10

April 2003

3-11

Adaptive Rate Feature

The Adaptive Rate feature is designed to find the best rate possible for your DSL
loop conditions. After the DSL loop is up, configure the card for a fixed rate by
setting the minimum DSL rate equal to the maximum DSL rate. The configuration
options are available from the DSL Interface Options screen.

Setting the DSL Line Rate

Adaptive Rate is controlled from the DSL Interface Options screen by setting the
Max DSL Rate and Min DSL Rate configuration options. These options are only
available if the card is configured as an STU-C.

To access the DSL Interface Options screen, follow this menu selection sequence:

Main Menu

→

C

onfiguration

→

Current Configuration

→

DSL Port

To enable Adaptive Rate, set the Min DSL Rate to a value lower than the Max DSL
Rate setting. For Fixed Rate, set the Min DSL Rate equal to the Max DSL Rate. If
the TDM SHDSL card cannot train at minimum DSL rate set, an alarm will be
generated. See

DSL Interface Options

in Appendix A,

Configuration Options

, for

more information.

main/config/dsl_interface

Slot 4 Model: 8799

DSL INTERFACE OPTIONS

Port Status: Enable

Estimated Line Length: Long

Startup Margin: 0dB

Max DSL Rate: 2056 kbps

Min DSL Rate: 2056 kbps

EIA-530 Payload Rate: 2048 kbps

Remotely Initiated Loopback: Enable

Circuit Identifier: Clear

--------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu MainMenu Exit

Save

«
...
33
34
35
36
37
...
»

Содержание Hotwire 8799



























































































































































Отзывы:

Нет отзывов