Paradyne Hotwire 8799 Скачать руководство пользователя страница 22

Страница: 22 / 154

2. Using the Asynchronous Terminal Interface

2-8

April 2003

8799-A2-GB20-10

Switching Between Screen Areas

Select Ctrl-a to switch between the two screen areas.

Procedure

To access the function keys and message area below the dotted line:

1. Press Ctrl-a to switch from the screen area to the function keys.

2. Enter the designated (underlined) character for the function key or press the

Tab key until you reach the desired function key.

Example:

To save the current options, type

(Save).

3. Press Enter. The function is performed.

4. To return to the screen area above the dotted line, press Ctrl-a again.

ain/config/dsl_interface

Slot: 4 Model: 8799

Port: 1

DSL INTERFACE OPTIONS

Port Status: Enable

Estimated Line Length: Long

Startup Margin: 4dB

Max DSL Rate: 2056 kbps

Min DSL Rate: 2056 kbps

EIA-530 Payload Rate: 2048 kbps

Remotely Initiated Loopback: Enable

Circuit Identifier: Clear

--------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu MainMenu Exit

Save

Содержание Hotwire 8799



























































































































































Результаты поиска

Содержание Hotwire 8799

Отзывы:

Paradyne Hotwire 8799, Руководство пользователя, Страница: 22 / 154

Результаты поиска

Содержание Hotwire 8799

Отзывы: