Paradyne Hotwire 8799 Скачать руководство пользователя страница 109

Страница: 109 / 154

A. Configuration Options

8799-A2-GB20-10

April 2003

A-35

Inband Management Channel

To access the Inband Management Channel screen, follow this menu selection
sequence:

Main Menu

→

Configuration

→

Current Configuration

→

Management and Communication

→

Inband Management Channel

Table A-13. Inband Management Channel Options (1 of 3)

Inband Management Select

Possible Settings:

Enable,

Disable

Default Setting:

Disable

Specifies whether data on the selected port and time slot will be sent according to the
cross connect configuration or to the MCC card instead.

Enable

– Enables the Inband Management Channel.

Disable

– Disables the Inband Management Channel.

Inband Management Type

Possible Setting:

PPP, Frame Relay

Default Setting:

PPP

Specifies the type of data the Inband Management Channel will accept.

PPP

– The Inband Managment Channel will accept Point-to-Point Protocol (PPP) data.

Frame Relay

−

The Inband Management Channel will accept Frame Relay data.

main/config/management/inband

Slot: 4 Model: 8799

INBAND MANAGEMENT CHANNEL

Inband Management Select: Enable

Inband Management Type: Frame Relay

Inband Management Port: 1

Inband Management Time Slot: 1

Inband Management DLCI: 16

Inband Management LMI: Standard

Backup Inband Management Port: 2

Backup Inband Management Time Slot: 1

Backup Inband Management DLCI: 16

-------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu MainMenu Exit

Save

Содержание Hotwire 8799



























































































































































Результаты поиска

Содержание Hotwire 8799

Отзывы:

Paradyne Hotwire 8799, Руководство пользователя, Страница: 109 / 154

Результаты поиска

Содержание Hotwire 8799

Отзывы: