Paradyne Hotwire 8799 Скачать руководство пользователя | Manualshive

Страница: 116 / 154

background image

B. Standards Compliance for SNMP Traps

B-2

April 2003

8799-A2-GB20-10

linkUp and linkDown

The link SNMP traps are:

linkUp

– The card recognizes that one of the communication interfaces is

operational.

linkDown

– The card recognizes that one of the communication interfaces is

not operational.

The network and synchronous port interfaces (physical sublayer) are represented
by an entry in the MIB-II interfaces table and supported by the DS1 MIB.

The following list describes the conditions that define linkUp and linkDown:

linkUp/Down Variable-Bindings

ifIndex (RFC 2863 (was 1573))

This object provides the index into the ifTable and potentially into tables in other MIBs.
The ifIndex included with the trap consists of the slot number times 1000, plus:

– 2

Backplane HDLC Interface

– 3 – 10

DSL E1 Interface, Port 1 – Port 8

– 15 – 22 G.703, Port 1 – Port 8

– 39 – 46 EOC management link, DSL1– DSL8

ifAdminStatus (RFC 2863). This object specifies the desired state of the interface:

– up(1)

DSL: DSL link is enabled.
G.703: G.703 interface is enabled.

– down(2)

DSL: DSL link is disabled.
G.703: G.703 interface is disabled.

– testing(3)

A test is active on the interface (currently not supported).

ifOperStatus (RFC 2863). This object specifies the current operational state of the
interface:

– up(1)

DSL: DSL link is established.
G.703: No alarm condition exists.

– down(2)

DSL: DSL link is not established.
G.703: An alarm condition exists.

– testing(3)

DSL: DSL link is in Test mode.
G.703: G.703 interface is in Test mode.

– dormant(5)

DSL: DSL link is in training.

i

fType (RFC 2863). This object is the type of interface:

– e1(19)

Used for the G.703 E1 interface.

– shdsl (169)

Used for the DSL interface.

«
...
114
115
116
117
118
...
»

Содержание Hotwire 8799



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Hotwire 8799

Бренд: Keysight Technologies Страницы: 64

Бренд: METREL Страницы: 59

Бренд: Extech Instruments Страницы: 16

Бренд: Clarke Страницы: 12

Бренд: Oakton Страницы: 76

Бренд: Giga-tronics Страницы: 17

Бренд: Sabtronics Страницы: 42

Бренд: Pro's Kit Страницы: 28

Бренд: Tenmars Страницы: 28

Бренд: PANCONTROL Страницы: 221

Бренд: Raisecom Страницы: 86

Бренд: Lascar Страницы: 6

Triplex DVMRe 16eZT

Бренд: GE Security Страницы: 81

Бренд: Keithley Страницы: 60

MX2820 STS-1 MUX

Бренд: ADTRAN Страницы: 2

Бренд: Amprobe Страницы: 88

Бренд: Amprobe Страницы: 72

Бренд: Amprobe Страницы: 182

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды