Paradyne Hotwire 8799 Скачать руководство пользователя страница 85

Страница: 85 / 154

A. Configuration Options

8799-A2-GB20-10

April 2003

A-11

Time Slot 16

Possible Settings:

Signaling_CCS, Signaling_CAS, Data

Default Setting:

Signaling_CCS

Specifies how the G.703 interface is being used.

Signaling_CCS

– Time slot 16 is used for Common Channel Signaling (the card is in

voice mode).

Signaling_CAS

– Time slot 16 is used for Channel Associated Signaling (the card is in

voice mode). The multiframe pattern is added to Timeslot 16.

Data

– Time slot 16 is used for data (the card is in data mode).

Primary Clock Source

Possible Settings:

Internal, G.703

Default Setting:

Internal

Determines the primary clock source for the unit in Bypass mode.

Primary Clock Source appears only when DSL Mode is set to STU-C (see

Table A-6, System Options

) and the card is not in Cross Connect mode.

Internal

– The clock source is derived from the System Clock. If the System Clock is

configured for Internal, then clocking is derived from the internal oscillator.

G.703

– Specifies the unit’s G.703 interface as primary clock source.

Table A-4.

G.703 Interface Options (2 of 2)

Содержание Hotwire 8799



























































































































































Результаты поиска

Содержание Hotwire 8799

Отзывы:

Похожие инструкции для Hotwire 8799

Бренды по названию

Популярные бренды

Paradyne Hotwire 8799, Руководство пользователя

Результаты поиска

Содержание Hotwire 8799

Отзывы:

Похожие инструкции для Hotwire 8799

Бренды по названию

Популярные бренды