Paradyne Hotwire 8799 Скачать руководство пользователя страница 45

Страница: 45 / 154

4. Monitoring the Card

8799-A2-GB20-10

April 2003

4-9

Viewing DSL Error Statistics

The line card maintains error statistics on the DSL interface for each port.

To view DSL Error Statistics, follow this menu selection sequence:

Main Menu

→

Status

→

Performance Statistics

→

DSL Error Statistics

The following DSL Error Statistics are collected for the selected port:

ES (Errored Seconds):

Seconds during which one or more Cyclic

Redundancy Check (CRC) errors or Loss of Sync Word (LOSW) defects has
occurred. Maximum value is 900.

SES (Severely Errored Seconds):

Seconds during which 50 or more CRC

anomalies or one or more LOSW defects has occurred. Maximum value
is 900.

UAS (Unavailable Seconds):

Seconds during which the SHDSL line is

unavailable. The SHDSL line becomes unavailable after 10 contiguous SES.
Maximum value is 900.

LOSWS (Loss of Sync Word Seconds):

Seconds during which the SHDSL

line had a Loss of Sync Word defect. Maximum value is 900.

main/status/performance/dsl_error

Slot: 4: Model: 8799

Port: 3 DSL ERROR STATISTICS

Current Interval Timer: 2

--------------------------------------------------------------------------------

---ES--- ---SES--- --UAS--- --LOSWS---

Near Far Near Far Near Far Near Far

Current Int: 000 000 000 000 000 000 000 000

Interval 01 000 000 000 000 000 000 000 000

Interval 02 000 000 000 000 000 000 000 000

Interval 03 000 000 000 000 000 000 000 000

Interval 04 000 000 000 000 000 000 000 000

Interval 05 000 000 000 000 000 000 000 000

Interval 06 000 000 000 000 000 000 000 000

Interval 07 000 000 000 000 000 000 000 000

Worst Interval: 24 09 14 08 18 18 18 18

Near Tot(valid): 00010 00000 00000 00000

Far Tot(valid): 00010 00000 00000 00000

--------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu MainMenu Exit

PgUp PgDn ClrNear ClrFar

Select 1, 2, 3, 4, 5, 6, 7, 8. Loss at DSL, Pt 3

Содержание Hotwire 8799



























































































































































Результаты поиска

Содержание Hotwire 8799

Отзывы:

Похожие инструкции для Hotwire 8799

Бренды по названию

Популярные бренды

Paradyne Hotwire 8799, Руководство пользователя

Результаты поиска

Содержание Hotwire 8799

Отзывы:

Похожие инструкции для Hotwire 8799

Бренды по названию

Популярные бренды