Paradyne Hotwire 8799 Скачать руководство пользователя страница 112

Страница: 112 / 154

A. Configuration Options

A-38

April 2003

8799-A2-GB20-10

The Cross Connect Mode screen appears.

5. Configure the G.703 port to be used for Inband Management to DS0

Cross-connect and save your changes.

6. Use the Inband Management Channel screen on the 8799 line card to

configure Inband Management. From the 8799 line card, follow this menu
selection sequence:

Main Menu

→

Configuration

→

Current Configuration

→

Management and Communication

→

Inband Management Channel

main/config/xConnect_mode

Slot: 18 Model: 8799

CROSS CONNECT MODE

Source Destination

G.703 MODE DSL

1 DS0 Cross-connect Unassigned

2 DS0 Cross-connect Unassigned

3 DS0 Cross-connect Unassigned

4 DS0 Cross-connect Unassigned

5 DS0 Cross-connect Unassigned

6 DS0 Cross-connect Unassigned

7 DS0 Cross-connect Unassigned

8 DS0 Cross-connect Unassigned

Assign_DS0s

--------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu MainMenu Exit

Save Clear_All

main/config/management/inband

Slot: 4 Model: 8799

INBAND MANAGEMENT CHANNEL

Inband Management Select: Enable

Inband Management Type: PPP

Inband Management Port: 1

Inband Management Time Slot: 1

-------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu MainMenu Exit

Save

Содержание Hotwire 8799



























































































































































Результаты поиска

Содержание Hotwire 8799

Отзывы:

Похожие инструкции для Hotwire 8799

Бренды по названию

Популярные бренды

Paradyne Hotwire 8799, Руководство пользователя

Результаты поиска

Содержание Hotwire 8799

Отзывы:

Похожие инструкции для Hotwire 8799

Бренды по названию

Популярные бренды