Paradyne Hotwire 8799 Скачать руководство пользователя страница 58

Страница: 58 / 154

4. Monitoring the Card

4-22

April 2003

8799-A2-GB20-10

The following information displayed in the Identity screen is stored in the card:

Model Number:

The 9-character model number of the card representing the

product family, model, and feature.

Serial Number:

The 7-digit serial number of the card.

Software Revision:

The software revision level of the firmware installed in the

card.

Hardware Revision:

The hardware revision level of the main circuit card

assembly in the card.

DSL Software Revision:

The software revision level of the DSL transceiver

installed in the card.

DSL Hardware Revision:

The hardware revision level of the DSL transceiver

installed in the card.

DSL Line Code:

Displays SHDSL as the type of line code the card is using.

Содержание Hotwire 8799



























































































































































Результаты поиска

Содержание Hotwire 8799

Отзывы:

Paradyne Hotwire 8799, Руководство пользователя, Страница: 58 / 154

Результаты поиска

Содержание Hotwire 8799

Отзывы: