Paradyne Hotwire 8799 Скачать руководство пользователя страница 119

Страница: 119 / 154

B. Standards Compliance for SNMP Traps

8799-A2-GB20-10

April 2003

B-5

SHDSL Traps

The following table lists the HDSL2-SHDSL-LINE MIB traps supported by the card.

SNMP Trap

Description

Variable Binding(s)

hdsl2ShdslLoopAtten
Crossing(1)

The loop attenuation
threshold has been
reached/exceeded for the
HDSL2/SHDSL segment
endpoint identified.

hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointThreshLo
opAttenuation

hdsl2ShdslSNRMargin
Crossing(2)

The SNR Margin
threshold has been
reached/exceeded for the
HDSL2/SHDSL segment
endpoint identified.

hdsl2ShdslEndpointCurr
SnrMrgn,
hdsl2ShdslEndpointThresh
SNRMargin

hdsl2ShdslPerfESThresh
(3)

The Errored Seconds
threshold has been
reached/exceeded for the
HDSL2/SHDSL segment
endpoint identified.

hdsl2ShdslEndpointCurr15Min
ES,
hdsl2ShdslEndpointThreshES

hdsl2ShdslPerfSESThresh
(4)

The Severely Errored
Seconds threshold has
been reached/exceeded
for the HDSL2/SHDSL
segment endpoint
identified.

hdsl2ShdslEndpointCurr15Min
SES,
hdsl2ShdslEndpointThresh
SES

hdsl2ShdslPerfCRC
anomaliesThresh(5)

The CRC Anomalies
threshold has been
reached/exceeded for the
HDSL2/SHDSL segment
endpoint identified.

hdsl2ShdslEndpointCurr15Min
CRCAnomalies,
hdsl2ShdslEndpointThresh
CRCAnomalies

hdsl2ShdslPerfLOSWS
Thresh(6)

The Loss of Sync Word
Seconds threshold has
been reached/exceeded
for the HDSL2/SHDSL
segment endpoint
identified.

hdsl2ShdslEndpointCurr15Min
LOSWS,
hdsl2ShdslEndpointThresh
LOSWS

hdsl2ShdslPerfUAS
Thresh(7)

The Unavailable Seconds
threshold has been
reached/exceeded for the
HDSL2/SHDSL segment
endpoint identified.

hdsl2ShdslEndpointCurr15Min
UAS,
hdsl2ShdslEndpointThresh
UAS

hdsl2ShdslSpanInvalidNum
Repeaters(8)

A mismatch has been
detected between the
number of
repeater/generator units
configured for an
HDSL/SHDSL line and
the number of units
discovered on the EOC

hdsl2ShdslSpanConfNum
Repeaters

Содержание Hotwire 8799



























































































































































Результаты поиска

Содержание Hotwire 8799

Отзывы:

Paradyne Hotwire 8799, Руководство пользователя, Страница: 119 / 154

Результаты поиска

Содержание Hotwire 8799

Отзывы: