Paradyne Hotwire 8799 Скачать руководство пользователя

Страница: 60 / 154

5. Testing

5-2

April 2003

8799-A2-GB20-10

Running DSL and G.703 Tests

DSL and G.703 tests run on the DSL and G.703 interfaces. These tests require
the participation of your network service provider.

To access the DSL & G.703 Tests screen, follow this menu selection sequence:

Main Menu

→

Test

→

DSL & G.703 Tests

Use the

Command

column to start or stop a test. When the

Status

column shows

that a test is Inactive,

Start

is displayed; when a test is Active,

Stop

is displayed.

Position the cursor at the desired Start or Stop command and press Enter. The

Results

column displays the test duration.

Selecting Abort All Tests from the Test menu will not disrupt a network-initiated
loopback.

NOTES:

The Send and Monitor 511 test is not available in all firmware releases.

When Send and Monitor 511 is enabled, ResetMon is available to reset the
error counter to zero.

main/test/dsl_G.703

Slot: 4 Model: 8799

Port: 4

DSL & G.703 TESTS

Test Command Status Results

--------------------------------------------------------------------------------

Local Loopbacks

DSL Loopback: Start Inactive 00:00:00

G.703 Repeater Loopback: Start Inactive 00:00:00

G.703 DTE Loopback: Start Inactive 00:00:00

Remote Loopbacks

Send Line Loopback: Down Send Inactive 00:00:00

Network Pattern Tests

Send and Monitor 511 Stop Active hh:mm:ss - Errors 99999+

--------------------------------------------------------------------------------

Ctrl-a to access these functions, ESC for previous menu MainMenu Exit

ResetMon

Содержание Hotwire 8799



























































































































































Результаты поиска

Содержание Hotwire 8799

Отзывы:

Похожие инструкции для Hotwire 8799

Бренды по названию

Популярные бренды

Paradyne Hotwire 8799, Руководство пользователя

Результаты поиска

Содержание Hotwire 8799

Отзывы:

Похожие инструкции для Hotwire 8799

Бренды по названию

Популярные бренды