Paradyne Hotwire 8799 Скачать руководство пользователя страница 14

Страница: 14 / 154

1. About the Hotwire 8799 Line Card

1-6

April 2003

8799-A2-GB20-10

SNMP Management Capabilities

The line card supports SNMP Version 1, and can be managed by any industry-
standard SNMP manager and accessed using SNMP by external SNMP
managers.

Management Information Base (MIB) Support

For a detailed description of supported MIBs, visit Paradyne’s Web site at

www.paradyne.com

. The following MIBs are supported:

MIB II (RFC 1213 and RFC 2863 (was 1573))

– Defines the general objects

for use with a network management protocol in TCP/IP internets and provides
general information about the unit. MIB II is backward-compatible with MIB I.

DS1/E1 MIB (RFC 2495 (was 1406))

– Reports the performance status of the

G.703 interface and supports the features found on the G.703 Performance
Statistics screen.

Entity MIB (RFC 2037)

– Supports all DSLAM cards.

Enterprise MIBs

– Supports

configuration, status, statistics, and tests.

SHDSL MIB (draft-ietf-adslmib-hdsl2.txt)

– Supports SHDSL configuration,

status, statistics, and tests.

SNMP Trap Support

The Hotwire 8799 Line Card supports traps as defined in RFC 1215. They may
include variable-bindings specified in the following MIBs:

MIB II (RFC 2863)

– Defines the general objects for use with a network

management protocol in TCP/IP internets and provides general information
about the 8799 line card. MIB II is backward-compatible with MIB I.

Enterprise MIBs

– Supports

configuration, status, statistics, and tests.

02-17111

G.703

8610

DSLAM

Network

7996

INPUT

48VDC CLASS 2 OR

LIMITED PWR SOURCE

RTN

48V

T5A

POSITION

STACK

ALM

DC FUSES

T4A, MIN. 48V

DC PWR

FAN

OUT

SERIAL

MCC

SYSTEM

Alr

Test

250V

SYSTEM

Alr

Test

G.703 ALRM

DSL POR

LINK-UP

SYSTEM

Alr

Test

G.703 ALRM

DSL POR

LINK-UP

SDSL

8715

Router

SNMP NMS

Ethernet
Interface

TDM SHDSL

EOC

Data

Voice

Operation, Maintenance
and Provisioning Center

Ethernet

LAN

G.703 ALRM

DSL POR

LINK-UP

8799

Содержание Hotwire 8799



























































































































































Результаты поиска

Содержание Hotwire 8799

Отзывы:

Похожие инструкции для Hotwire 8799

Бренды по названию

Популярные бренды

Paradyne Hotwire 8799, Руководство пользователя

Результаты поиска

Содержание Hotwire 8799

Отзывы:

Похожие инструкции для Hotwire 8799

Бренды по названию

Популярные бренды