Paradyne Hotwire 8799 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 154

background image

5. Testing

8799-A2-GB20-10

April 2003

5-3

DSL Line Loopback

A DSL Line Loopback (LLB) loops the received signal on the DSL port back to the
DSL port without change. If the DSL port is configured in a DSL cross connection,
the corresponding G.703 time slots will be filled with ones. On ports in Bypass
mode or in a DS1 cross connection, an Alarm Indication Signal (AIS) is sent on the
G.703 port.

Procedure

To run a DSL Line Loopback:

1. Position the cursor at the Start command next to DSL Loopback on the DSL &

G.703 Tests screen.

2. Press Enter.

The Start command is changed to Stop. Status is changed to Active.

3. To manually stop the test, verify that the cursor is positioned at the Stop

command.

4. Press Enter.

Status is changed to Inactive.

The DSL Line Loopback cannot be started when any other loopback is in progress
and will only start if the DSL link is up.

DSL
Port

G.703
Port

E1

LIU

Framer

Framer

Transceiver

AIS

02-17127

«
...
59
60
61
62
63
...
»

Содержание Hotwire 8799



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Hotwire 8799

Бренд: jenway Страницы: 36

Бренд: ETS-Lindgren Страницы: 34

Бренд: KPS Страницы: 20

Бренд: Jeulin Страницы: 18

Everywhereyoulook T3SP-D4MX

Бренд: Teledyne Страницы: 29

Бренд: PeakTech Страницы: 64

Бренд: Wavetek Страницы: 36

Бренд: Mastech Страницы: 26

Бренд: YATO Страницы: 64

Бренд: National Instruments Страницы: 128

Бренд: Navair Страницы: 23

Бренд: Ohmeron Страницы: 17

Бренд: Crenova Страницы: 10

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 5

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 4

Бренд: Datacom Страницы: 106

Бренд: PANCONTROL Страницы: 192

Бренд: HoldPeak Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды