Paradyne 3160-A3 Скачать руководство пользователя | Manualshive

Страница: 96 / 298

background image

3. Operation

3-62

February 2001

3160-A2-GB21-90

5. Select User.

6. Press F1 (Next) until the Com Port configuration option appears.

7. Select Enab to enable the COM port for the carrier-mounted DSU/CSU.

The carrier COM port provides the following functionality:

If configured for ASCII, only one ASCII device may be used for the carrier. (If
two COM ports are configured for ASCII, neither will work.)

If configured for Mgmt, each device in the carrier can support an Mgmt COM
port; however, each Mgmt COM port must be connected to a different subnet.
To facilitate IP data routing, the device with the closest link to the SNMP
manager or Telnet client should be configured as the IP Bus Master.

If configured for either ASCII or Mgmt, the carrier COM port may be configured
to control an external device (e.g., modem, x.25 PAD) through the use of AT or
user-specified commands.

The set of valid characters for control of the carrier external COM port device is as
follows:

The numbers: 0–9

The lowercase letters: a–z

The uppercase letters: A–Z

The space (“ ”) character

The ASCII symbols (in ascending order, based on the ASCII code)

The End Of Line (EOL) symbol:

←

The caret (“^”) control character is used to select non-printable ASCII
characters. The caret “^” must be followed by one character which together
form the control sequence.

Table 3-7, Control Sequence

, defines all of the

available control sequences.

F1

F2

F3

Edit:
Chan Gen User

F1

F2

F3

Com Port:
Next Enab Disab

«
...
94
95
96
97
98
...
»

Содержание 3160-A3











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3160-A3

Бренд: Sagem Страницы: 19

System x3630 M4

Бренд: IBM Страницы: 7

SmartSwitch Router

Бренд: Cabletron Systems Страницы: 338

Бренд: Garland Страницы: 4

Бренд: Sangoma Страницы: 6

Бренд: Lattice Semiconductor Страницы: 15

Бренд: Quatech Страницы: 27

Бренд: IEI Technology Страницы: 3

Бренд: CSS Страницы: 2

Бренд: SUNRICH TECHNOLOGY Страницы: 5

Бренд: Alesis Страницы: 46

RUGGEDSWITCH RS900G

Бренд: RuggedCom Страницы: 23

Parallel Printer Card PIOC

Бренд: B&B Electronics Страницы: 16

DL-DVI-Vision-IP Series

Бренд: G&D Страницы: 228

CY62136EV30 MoBL

Бренд: Cypress Semiconductor Страницы: 12

GSM7224v2 - Layer 2 Managed Gigabit Switch

Бренд: NETGEAR Страницы: 3

LatticeMico GPIO

Бренд: Lattice Semiconductor Страницы: 28

Бренд: Goobay Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды