Paradyne 3160-A3 Скачать руководство пользователя | Manualshive

Страница: 220 / 298

background image

E. SNMP MIB Objects

E-6

February 2001

3160-A2-GB21-90

Interface Group – “ifDescr” Object (ifEntry 2)

This object provides information about the interface. Each interface displays a text
string as shown below:

Interface Group – “ifType” Object (ifEntry 3)

This object identifies the type of the interface based on the physical/link protocol(s)
immediately below the network layer. Only the following values are supported by
the DSU/CSU:

ds1 – Used for the network and DTE Drop/Insert (DSX-1) interfaces.

propPointToPointSerial(22) – Used for the synchronous data ports. Used for
the MODEM or COM port when the port is not configured as the SNMP
management interface.

ppp(23) – Used for the MODEM, AUX, or COM port when the port is
configured for PPP.

slip(28) – Used for the MODEM or COM port when the port is configured for
SLIP.

Interface Group – “ifMtu” Object (ifEntry 4)

This object identifies the largest datagram that can be sent or received on the
interface. It is applicable only to the interface configured as the SNMP
management link. This object is zero for all other interfaces.

Network T1:

“

Network T1.

[

Company Name

]

T1 DSU/CSU, Hardware

Version:

[CCA number for the CSU board]”.

DTE T1:

“

DTE T1.

[

Company Name

]

T1 DSU/CSU, Hardware

Version:

[CCA number for the CSU board]”.

COM:

“

COM port.

[

Company Name

]

T1 DSU/CSU, Hardware

Version:

[CCA number for the CSU board for the standalone,

or the CCA number for the DSU board for the carrier]”.

Modem:

“

MODEM port.

[

Company Name

]

T1 DSU/CSU, Hardware

Version:

[CCA number for the CSU board]”.

AUX:

“

AUX port.

[

Company Name

]

T1 DSU/CSU, Hardware

Version:

[CCA number for the CSU board]”.

Data Ports:

“

Data Port n.

[

Company Name

]

T1 DSU/CSU, Hardware

Version:

[CCA number for the DSU board]”

(where

n

is 1 to 4).

«
...
218
219
220
221
222
...
»

Содержание 3160-A3











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3160-A3

i-bus KNX IPR/S 3.5.1

Бренд: ABB Страницы: 44

PCMCIA WIRELESS ASAPTER DWL-650

Бренд: D-Link Страницы: 5

PowerLine DHP-W611AV

Бренд: D-Link Страницы: 78

IES615-2D Series

Бренд: 3onedata Страницы: 3

Бренд: 3One data Страницы: 5

Бренд: 3onedata Страницы: 33

LS42 - BladeCenter - 7902

Бренд: IBM Страницы: 56

Бренд: IBM Страницы: 2

BladeCenter Management Module

Бренд: IBM Страницы: 78

Бренд: IBM Страницы: 110

Remote Supervisor Adapter II

Бренд: IBM Страницы: 132

Бренд: LORD Страницы: 9

Бренд: QNO Страницы: 106

Бренд: Face Страницы: 8

Бренд: TP-Link Страницы: 2

Бренд: Fostex Страницы: 20

Бренд: ZyXEL Communications Страницы: 2

Бренд: Omega Engineering Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды