Paradyne 3160-A3 Скачать руководство пользователя | Manualshive

Страница: 182 / 298

background image

C. Configuration Options

C-38

February 2001

3160-A2-GB21-90

Def Netwk: None
Next None IPBus Com Modem Aux FDL EDL1 EDL2 EDL3
EDL4 Prev

Default Network Destination. Specifies the default network destination. This configuration
option specifies where the default network is connected. For example, if the default
network is connected to the communication port, you select Com. If the default network is
connected to the far-end 31xx Series device over the FDL, you select FDL. The routing
protocol uses the default network destination to route data that does not have a specific
route.

None – No default network destination. Data that cannot be routed is discarded.

IPBus – The default network destination is the IP Bus on the carrier backplane. This
selection only appears for carrier-mounted DSU/CSUs which are not configured as the IP
Bus Master.

Com – The default network destination is the communication port. This selection only
appears if the Com Use configuration option is set to Mgmt.

Modem – The default network destination is the modem port. This selection only appears
if the Modem Use configuration option is set to Mgmt. This selection does not appear on
carrier-mounted DSU/CSUs.

Aux – The default network destination is the auxiliary port. This selection only appears if
the Aux Use configuration option is set to Mgmt.

FDL – The default network destination is FDL. This selection only appears if the FDL
management link is enabled.

EDL

n – For 2-port and 4-port DSU/CSUs, the default network destination is the EDLn port

(where

n is 1–4). This selection only appears in 2-port and 4-port DSU/CSUs if the

synchronous data port’s EDL management link is enabled.

NOTE: If the chosen default network link is disabled or down, data is discarded. Return
to this menu and choose another default network.

Table C-9.

General Management Configuration Options (7 of 7)

«
...
180
181
182
183
184
...
»

Содержание 3160-A3











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3160-A3

Бренд: D-Link Страницы: 2

Бренд: NEC Страницы: 10

Бренд: NEC Страницы: 8

SISPM1040-582-LRT

Бренд: Lantronix Страницы: 2

Бренд: Lantronix Страницы: 7

Maestro E220 Series

Бренд: Lantronix Страницы: 25

Бренд: National Instruments Страницы: 162

Бренд: QNAP Страницы: 20

Бренд: Queclink Страницы: 9

BladeCenter Management Module

Бренд: IBM Страницы: 184

Бренд: Commell Страницы: 9

HHM Series HHM2411

Бренд: TDK Страницы: 2

Бренд: Rosewill Страницы: 3

Бренд: QNAP Страницы: 54

JetNet 3508-LVDC

Бренд: Korenix Страницы: 16

Бренд: Supermicro Страницы: 15

Бренд: Tripp Lite Страницы: 3

Бренд: Zonet Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды