Paradyne 3160-A3 Скачать руководство пользователя | Manualshive

Страница: 53 / 298

background image

3. Operation

3160-A2-GB21-90

February 2001

3-19

Procedure

To copy the configuration options to one or all ports:

1. From the Port Select screen, select Copy.

2. Select the port

from

which you want to copy the configuration options using

the corresponding Function key.

3. Select the port

to

which you want to copy the configuration options using the

corresponding Function key. Or, press F1 (All) to choose to copy to all ports.

Configuring the DSU/CSU for SNMP or Telnet Access

To configure the DSU/CSU for SNMP or Telnet access:

Enable the SNMP agent or Telnet server within the DSU/CSU (see

Appendix C,

Configuration Options

).

Select and configure the port that provides the link to the SNMP or Telnet
system.

Set the Internet Protocol (IP) address and subnet mask needed to access the
DSU/CSU (see

Appendix F,

IP Network Addressing Scenarios

).

Select the link layer protocol (PPP or SLIP) for the port that provides the link to
the SNMP or Telnet system.

For SNMP links, specify the two community names (and their access levels)
that are allowed to access the device’s Management Information Base (MIB).

For SNMP links, configure the device to send traps to the SNMP manager, if
desired.

Specify the Telnet password or SNMP validation options, if desired (see

Appendix C,

Configuration Options

).

F1

F2

F3

Port Select:
Copy Prt1 Prt2

F1

F2

F3

Copy From:
Prt1 Prt2 Prt3

F1

F2

F3

Copy To:
All Prt1 Prt2

«
...
51
52
53
54
55
...
»

Содержание 3160-A3











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3160-A3

Verizon DSL-2750B

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 4

Бренд: Lauterbach Страницы: 61

Бренд: 4IPNET Страницы: 97

Бренд: N-Tron Страницы: 62

Бренд: PaloAlto Networks Страницы: 3

Adapter Bracket

Бренд: Paradyne Страницы: 1

Бренд: NETGEAR Страницы: 2

Бренд: Usr Страницы: 2

Бренд: Asante Страницы: 150

Бренд: Giacomini Страницы: 2

Бренд: Avaya Страницы: 73

PowerBeam PBE-5AC-400-ISO

Бренд: Ubiquiti Страницы: 23

OMB-DAQBOARD-500 Series

Бренд: Omega Страницы: 48

Бренд: ANEP Страницы: 48

Бренд: Vecow Страницы: 61

PCMCIA High Speed Serial Card CE 232HSPCC

Бренд: B&B Electronics Страницы: 14

NetCon FBR-1409TX

Бренд: LevelOne Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды