Paradyne 3160-A3 Скачать руководство пользователя

Страница: 40 / 298

3. Operation

3-6

February 2001

3160-A2-GB21-90

Table 3-1.

System LEDs

Name

Color

Meaning

Green

Indicates the current operational state of the DSU/CSU.

ON: The DSU/CSU is operational and has power.

OFF: The DSU/CSU is performing a power-up self-test or a
system failure has occurred.

BLINKING: A software download is in progress.

FAST BLINK: The carrier-mounted DSU/CSU is currently
selected by the SDCP.

FAIL

Yellow

Indicates a system failure or a self-test.

ON: A device error/fault is detected or a reset has just occurred.

OFF: No system failures are detected.

BLINKING: A self-test is in progress.

TEST

Yellow

A system test is in progress.

ON: A loopback or pattern test has been initiated either locally, by
the network, or externally.

OFF: No tests are active.

Table 3-2.

Network Interface LEDs

Name

Color

Meaning

SIG

Green

Monitors the signal being received from the network.

ON: A recoverable signal is being received from the network.

OFF: The signal cannot be recovered from the network (a Loss of
Signal condition exists).

OOF

Yellow

Monitors Out Of Frame (OOF) conditions on the received
network signal.

ON: At least one OOF was detected on the signal during the
sampling period.

OFF: No OOFs were detected on the signal during the sampling
period.

ALRM

Yellow

Indicates whether an alarm condition exists on the received
network signal.

ON: An alarm condition (LOS, LOF, EER, Yellow, AIS) exists on
the received network signal. Use the Device Health and Status
command to determine the alarm type.

OFF: No alarm condition exists on the network interface signal.

EER

Yellow

Indicates the Excessive Error Rate (EER) has been exceeded on
the network interface.

NOTE: This LED is only valid when ESF framing is being used.

ON: The EER has been exceeded on the network interface.

OFF: The EER has not been exceeded on the network interface.

Содержание 3160-A3











































































































































































































































































































Результаты поиска

Содержание 3160-A3

Отзывы:

Похожие инструкции для 3160-A3

Бренды по названию

Популярные бренды

Paradyne 3160-A3, Руководство оператора

Результаты поиска

Содержание 3160-A3

Отзывы:

Похожие инструкции для 3160-A3

Бренды по названию

Популярные бренды