Paradyne 3160-A3 Скачать руководство пользователя | Manualshive

Страница: 230 / 298

background image

E. SNMP MIB Objects

E-16

February 2001

3160-A2-GB21-90

Near End Group – “dsx1CircuitIdentifier” Object (dsx1ConfigEntry 8)

This object is only supported on the Net T1 Interface.

Near End Group – “dsx1LoopbackConfig” Object (dsx1ConfigEntry 9)

This object specifies the loopback state of the T1 interfaces. Only the following
values are supported by the DSU/CSU.

dsx1NoLoop(1) – The T1 interface is not in a loopback state.

dsx1PayloadLoop(2) – Specifies that a Payload Loopback (PLB) is active for
the network interface or a Repeater Loopback (RLB) is active for the DTE
Drop/Insert (DSX-1) interface.

dsx1LineLoop(3) – Specifies that a Line Loopback (LLB) is active for the
network interface or a DTE Loopback (DLB) is active for the DTE Drop/Insert
(DSX-1) interface.

Near End Group – “dsx1LineStatus” Object (dsx1ConfigEntry 10)

This object specifies the line (alarm) status of the T1 interfaces. Only the following
values are supported by the DSU/CSU. More than one value may be active at a
time.

dsx1NoAlarm(1) – No alarm present.

dsx1RcvFarEndLOF(2) – A yellow alarm signal is being received.

dsx1RcvAIS(8) – An Alarm Indication Signal (AIS) is being received.

dsx1LossOfFrame(32) – An Out Of Frame condition has persisted for more
that 2.5 seconds (i.e., Red Alarm).

dsx1LossOfSignal(64) – A Loss of Signal condition has persisted for more that
2.5 seconds (i.e., Red Alarm).

dsx1LoopbackState(128) – The near end of the T1 interface is in a loopback
state.

dsx1Other Failure(4096) – An Excessive Error Rate (EER) has been detected
on the network interface.

Near End Group – “dsx1SignalMode” Object (dsx1ConfigEntry 11)

This object specifies whether Robbed Bit Signaling (RBS) is being used. This
object differs from the MIB definition in that it is “read-only" (not read/write) for
DSU/CSUs. Only the following values are supported by the DSU/CSU.

none(1) – No signaling is being used on this interface.

robbedBit(2) – Robbed Bit Signaling is being used on at least one DS0 on this
T1 interface.

«
...
228
229
230
231
232
...
»

Содержание 3160-A3











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3160-A3

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 2

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 28

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 2

Бренд: Farallon Страницы: 26

Бренд: Observint Страницы: 11

Бренд: Magma Страницы: 2

Бренд: Magnadyne Страницы: 13

Бренд: Octavo Страницы: 28

Бренд: Obihai Страницы: 2

Asynchronous SH7145F

Бренд: Renesas Страницы: 17

Optane Persistent Memory 200 Series

Бренд: Supermicro Страницы: 54

Hotwire 8775 MSDSL

Бренд: Paradyne Страницы: 10

Бренд: Abocom Страницы: 63

Бренд: Nakayo Страницы: 119

NOVA300 AML02304U1

Бренд: Nexxt Страницы: 75

Бренд: Xilinx Страницы: 29

Бренд: Amphenol Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды