Paradyne 3160-A3 Скачать руководство пользователя | Manualshive

Страница: 85 / 298

background image

3. Operation

3160-A2-GB21-90

February 2001

3-51

Procedure

To enter a password:

1. Use the

and

keys to position the cursor under the desired character.

You must enter a character before the

key moves the cursor to the next

space to the right. The

key is not destructive.

2. Enter the required password. Press F1 (Up) and F2 (Down) to scroll up and

down through the valid characters/numbers for the password. You have five
minutes to enter the correct password before the DSU/CSU ends the session.

3. Press F3 (Done) to indicate you are done entering the password. If you enter

an invalid password, the message

Invalid Password

appears.

Acquiring/Releasing the User Interface

You can access the user interface from either the front panel, the COM port, the
MODEM port (for standalone DSU/CSUs), or the SDCP (for carrier-mounted
DSU/CSUs). The DSU/CSU allows only one user interface to be active at a time.
The front panel is the default user interface at power-up or after a reset. It is also
the default during a software download or when a failure occurs at either the local
or remote PC interface.

You can switch an inactive user interface to active if:

The current active user interface has had no activity (no key was pressed) for
at least five minutes.

The active user interface has been released with the Release command.

The active interface connection is broken. This includes the call disconnect for
a modem interface or the termination of the front panel emulation program on
a locally-attached PC (if the PC supports DTR) or the termination of the async
terminal interface on a remote or locally attached terminal.

F1

F2

F3

Passwd:

xxxxxxxx

Up Down Done

«
...
83
84
85
86
87
...
»

Содержание 3160-A3











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3160-A3

Бренд: Panasonic Страницы: 4

Бренд: Dahua Страницы: 24

HAWA-Frontside 60/B

Бренд: hawa Страницы: 28

Бренд: Winext Страницы: 37

StorageWorks AIT 35GB AutoLoader

Бренд: Compaq Страницы: 4

Active Module Carrier VX402C-64

Бренд: C&H Страницы: 32

Бренд: EVOC Страницы: 57

Бренд: Rane Страницы: 128

Бренд: Acard Страницы: 34

Бренд: Shure Страницы: 113

PCMCIA High Speed Serial Card CE 232HSPCC

Бренд: B&B Electronics Страницы: 14

Бренд: Altimium Страницы: 12

Security Router X-PeditionTM

Бренд: Enterasys Страницы: 466

Бренд: Digital Audio Corporation Страницы: 164

Бренд: AES Страницы: 44

Бренд: Lanpro Страницы: 3

Бренд: Lefroy Brooks Страницы: 10

ExpressCard 11-in-1 Reader/Writer

Бренд: SIIG Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды