Paradyne 3160-A3 Скачать руководство пользователя | Manualshive

Страница: 146 / 298

background image

C. Configuration Options

C-2

February 2001

3160-A2-GB21-90

Management Configuration Options

The Management configuration options configure the DSU/CSU for SNMP or
Telnet access (

Table C-9, General Management Configuration Options

,

and

Table C-10, Management Trap Configuration Options

).

The configuration tables include a description of each configuration function and
its available selections. In the tables, the top line of each configuration option
entry indicates the factory default setting.

DTE Interface Configuration Options

NOTE:

These configuration options are only available for 2-port and 4-port
DSU/CSUs.

Table C-1.

DTE Interface Configuration Options (1 of 2)

DTE Port: Enab
Next Enab Disab Prev

DTE Drop/Insert (DSX-1) Port. Enables the use of the DTE Drop/Insert (DSX-1) port.

Enab – Allows the use of the DTE Drop/Insert (DSX-1) interface.

Disab – Prohibits the use of the DTE Drop/Insert (DSX-1) interface.

NOTE: When this configuration option is disabled, you cannot display or configure any
other DTE Interface configuration options. If the clock source configuration option is
set to DTE, it is changed to NET.

DTE Framing: ESF (Factory 1) D4 (Factory 2)
Next D4 ESF Prev

DTE Line Framing Format. Designates the framing format for the DTE Drop/Insert
(DSX-1) interface.

D4 – Configures for the D4 framing format.

ESF – Configures for the Extended Superframe framing format.

DTE Coding: B8ZS (Factory 1) AMI (Factory 2)
Next AMI B8ZS Prev

DTE Line Coding Format. Designates the line coding format to be used on the DTE
Drop/Insert (DSX-1) interface.

AMI – Uses the Alternate Mark Inversion coding format.

B8ZS – Uses the Bipolar 8 Zero Suppression coding format.

Equal: 0—133
Next 0—133 133—266 266—399 399—533 533—655 Prev

DTE Line Equalization. Specifies the DTE line equalization compensation parameters that
permit a standard DTE Drop/Insert (DSX-1) signal to be delivered over a distance of up to
655 feet.

«
...
144
145
146
147
148
...
»

Содержание 3160-A3











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3160-A3

Бренд: IBM Страницы: 72

Бренд: XDS Страницы: 99

Бренд: Makita Страницы: 2

Бренд: Magma Страницы: 2

Бренд: Magnadyne Страницы: 13

Бренд: National Instruments Страницы: 9

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 32

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 8

Бренд: SAF Страницы: 30

Бренд: Danfoss Страницы: 61

Marconi OMS 1200

Бренд: Ericsson Страницы: 136

Бренд: Advantech Страницы: 50

Wisenet XRN-6410RB2-24TB

Бренд: Hanwha Techwin Страницы: 124

Бренд: CopperOptics Страницы: 12

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 2

Emulation Memory Board R0E330850MSRC0

Бренд: Renesas Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды