Paradyne 3160-A3 Скачать руководство пользователя | Manualshive

Страница: 216 / 298

background image

E. SNMP MIB Objects

E-2

February 2001

3160-A2-GB21-90

MIB II (RFC 1213)

The objects defined by MIB II are organized into 10 different groups. The
DSU/CSU implements only those groups where the semantics of the group are
applicable to the implementation of a DSU/CSU. The MIB II object groups
supported or not supported by the 3100 Series devices are as follows:

System
Group

Supported.

Interface
Group

Supported for the network interface, the DTE Drop/Insert
(DSX-1) interface, the synchronous data ports, the COM port,
the AUX port, and the MODEM port. Interface statistics
(counters) apply to any port (COM, AUX, or MODEM),
whichever is defined as the SNMP management link.

Address
Translation
Group

Not supported since this group is not supported in MIB II.

IP Group

Supported.

ICMP Group

Supported.

TCP Group

Supported.

UDP Group

Supported.

EGP Group

Not supported since the EGP protocol is not supported by the
DSU/CSU.

Transmission
Group

Supported on the T1 interfaces using the DS1/E1 MIB.
Supported on the synchronous data ports using the
RS-232-like MIB. Supported on the COM, AUX, and MODEM
ports using the RS-232-like MIB.

SNMP Group

Supported.

«
...
214
215
216
217
218
...
»

Содержание 3160-A3











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3160-A3

Бренд: D-Link Страницы: 15

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 32

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 221

Express Ethernetwork DI-707P

Бренд: D-Link Страницы: 14

WS-650 lite Series

Бренд: Laurell Страницы: 84

Бренд: Yamaha Страницы: 24

Бренд: Yamaha Страницы: 5

Бренд: Compaq Страницы: 112

RouterBOARD SXT 5HnD

Бренд: MikroTik Страницы: 2

Бренд: SeaLevel Страницы: 17

Бренд: WHOOP Страницы: 26

BladeCenter Management Module

Бренд: IBM Страницы: 184

Бренд: Wintech Страницы: 21

Бренд: EMCIS Страницы: 14

kontron KBox E-420-R1K/V1K

Бренд: S&T Страницы: 82

Бренд: Idis Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды