Paradyne 3160-A3 Скачать руководство пользователя

Страница: 99 / 298

3. Operation

3160-A2-GB21-90

February 2001

3-65

Resetting the DSU/CSU

Use the Reset command to perform a power-on reset of the DSU/CSU.

Procedure

To reset the DSU/CSU:

1. From the top-level menu screen, press the

key until the Ctrl selection

appears on the screen.

2. Select Ctrl.

3. From the Control screen, press the

key until the Reset selection appears

on the screen.

4. Select Reset.

5. From the Device Reset screen, press F1 to initiate a reset of the DSU/CSU

(the power-up sequence screen appears). Press F2 instead to return to the
Control screen without initiating a reset.

Download Operations

NOTE:

The Download command is for use by service personnel only. Loss of primary
data could result from improper use.

Control:
ClrReg Reset

Device Reset:
Yes No

Содержание 3160-A3











































































































































































































































































































Результаты поиска

Содержание 3160-A3

Отзывы:

Похожие инструкции для 3160-A3

Бренды по названию

Популярные бренды

Paradyne 3160-A3, Руководство оператора

Результаты поиска

Содержание 3160-A3

Отзывы:

Похожие инструкции для 3160-A3

Бренды по названию

Популярные бренды