Paradyne 3160-A3 Скачать руководство пользователя | Manualshive

Страница: 173 / 298

background image

C. Configuration Options

3160-A2-GB21-90

February 2001

C-29

DialOut: Disab
Next Enab Disab Prev

Alarm and Trap Dial Out. Controls whether generated alarm or trap messages initiate a
call if the integral modem connection or carrier external communication port device
connection has not already been established. When enabled, a call is placed to the phone
number contained in the alarm directory (directory A). If the call cannot be completed and
the retry option is enabled, the alarm or trap message is held until the call is completed or
has been retried unsuccessfully once. If more than one alarm message is received while
waiting for a call retry, only the highest priority alarm message received is held; all
previous messages are discarded. When the modem port is configured as the SNMP
management link, up to 10 SNMP trap messages can be queued at the interface.

Enab – Enables automatic call initiation (dial out) if an alarm or trap message needs to be
sent.

Disab – Disables automatic call initiation. Trap messages sent to the modem port or
carrier external communication port device are queued (held) if an integral modem
connection or carrier external communication port device connection has not been
previously established. Alarm messages are not queued.

NOTE: For carrier-mounted DSU/CSUs, this configuration option is only available if the
communication port is enabled for an external device.

Call Retry: Disab
Next Enab Disab Prev

Call Retry on Alarm or Trap. Determines whether a call that cannot be completed (busy,
no answer, etc.) is retried. This affects calls that are initiated in attempting to send an
alarm or trap message to the modem port or carrier external communication port device. If
call retry is specified, the DSU/CSU attempts to complete the call after a configurable
delay.

Enab – Enables call retry. If enabled, the call is retried once per alarm or trap message. A
delay as specified by the dial-out delay time is imposed between call attempts. If an
alternate dial-out directory is specified, both the alarm directory as well as the alternate
directory are retried once.

Disab – Disables call retry. If a call setup cannot be completed it is not retried.

NOTE: For carrier-mounted DSU/CSUs, this configuration option is only available if the
communication port is enabled for an external device.

Dial Delay: 5
Next 1 2 3 4 5 6 7 8 9 10 Prev

Dial Out Delay Time on Alarm or Trap. Specifies the number of minutes to wait between
successive dial-out alarms or traps and before a retry attempt after failed alarm dial-outs.
The factory default is 5 minutes.

NOTE: For carrier-mounted DSU/CSUs, this configuration option is only available if the
communication port is enabled for an external device.

Table C-8.

Alarm Configuration Options (2 of 4)

«
...
171
172
173
174
175
...
»

Содержание 3160-A3











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3160-A3

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 86

Бренд: Konig Страницы: 73

Бренд: Conceptronic Страницы: 230

Supero SAS-826A

Бренд: Supero Страницы: 16

Surround Dongle

Бренд: Sennheiser Страницы: 18

kontron COMe-cEL6

Бренд: S&T Страницы: 99

Бренд: Patton electronics Страницы: 12

Бренд: Pressalit Care Страницы: 31

Бренд: Idis Страницы: 17

IGS-5225-20T4C2X

Бренд: Planet Страницы: 16

LMP-1202G-SFP Series

Бренд: ANTAIRA Страницы: 19

Бренд: Alarm Страницы: 5

FiberTwist G6426

Бренд: Genexis Страницы: 9

Disc Publisher XR

Бренд: Primera Страницы: 2

Бренд: TP-Link Страницы: 37

Бренд: Wyse Страницы: 8

Бренд: Acces Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды