Paradyne 3160-A3 Скачать руководство пользователя | Manualshive

Страница: 17 / 298

background image

3160-A2-GB21-90

February 2001

1-1

1

Introduction

Overview

The ACCULINK

®

316x DSU/CSU acts as an interface between the T1 digital

network and the customer premises equipment, converting signals received from
the DTE (Data Terminal Equipment) to bipolar signals that can be transmitted over
T1 lines. Typical applications include shared access to network-based services,
Local Area Network (LAN)/Wide Area Network (WAN) interconnection, and
fractional T1 network applications.

In addition to the T1 network interface and the DTE Drop/Insert (DSX-1) interface,
the Model 3160 provides two synchronous data ports while the Model 3164
provides four synchronous data ports. The Model 3165 provides one synchronous
data port, but does not provide the DTE Drop/Insert (DSX-1) interface.

The Model 3161 (carrier-mounted DSU/CSU) provides two ports in addition to the
DTE Drop/Insert (DSX-1) interface and is designed to fit into the COMSPHERE
3000 Series Carrier.

For more information about the carrier-mounted DSU/CSU, refer to the

ACCULINK

3151 CSU and 3161 DSU/CSU General Information Guide

and the

COMSPHERE

3000 Series Carrier Installation Manual

.

Features

The DSU/CSU optimizes network performance with a wide range of features such
as the following:

Software configuration menu displayed via a liquid crystal display (LCD) to
permit quick and easy operation, and elimination of complicated hardware
strapping.

Local or remote configuration and operation flexibility.

Several loopback capabilities and test pattern generators.

DTE Drop/Insert (DSX-1) capability.

Alarm message display/print capability.

Front panel emulation via Windows-based Front Panel Emulation software.

Integral modem for standalone DSU/CSUs.

«
...
15
16
17
18
19
...
»

Содержание 3160-A3











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3160-A3

Бренд: Vanguard Страницы: 121

IES615-2D Series

Бренд: 3onedata Страницы: 3

Бренд: 3One data Страницы: 5

Бренд: 3onedata Страницы: 33

Бренд: ICP DAS USA Страницы: 8

Бренд: Zenith Data Systems Страницы: 64

Бренд: Vonets Страницы: 8

Бренд: Konig Страницы: 73

Бренд: iDirect Страницы: 52

Бренд: Axis Страницы: 104

Бренд: Intel Страницы: 108

Бренд: ZyXEL Communications Страницы: 125

Бренд: Zonet Страницы: 53

Бренд: ZyXEL Communications Страницы: 244

Бренд: XtendLan Страницы: 52

Бренд: Ubiquiti Страницы: 28

Бренд: Rosco Страницы: 20

Бренд: ADS Technologies Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды