Paradyne 3160-A3 Скачать руководство пользователя | Manualshive

Страница: 171 / 298

background image

C. Configuration Options

3160-A2-GB21-90

February 2001

C-27

TnSession: Disab
Next Enab Disab Prev

Telnet Session Enable. Specifies whether the DSU/CSU responds to Telnet session
requests.

Enab – The DSU/CSU responds to Telnet session requests.

Disab – The DSU/CSU does not respond to Telnet session requests.

TnPaswd: Disab
Next Enab Disab Prev

Telnet Password Mode. Specifies whether a password is required for Telnet access.

Enab – A password is required for Telnet access.

Disab – A password is not required for Telnet access.

TnInActTm: Disab
Next Enab Disab Prev

Telnet Inactivity Timeout. Specifies whether the Telnet session disconnects after a period
of inactivity specified by the TnDiscTm configuration option.

Enab – The Telnet session disconnects after the period of inactivity specified by the
TnDiscTm configuration option.

Disab – The Telnet session does not disconnect due to inactivity.

TnDiscTm: 5
Next Up Down Save Prev

Telnet Disconnect Time. Specifies the period of time (1 to 60 minutes) before the Telnet
session disconnects due to inactivity. (The TnInActTm configuration option must be set to
Enab.) Use the left or right arrow key to position the cursor on the digit you want to
change. Use the Function keys (Up or Down) to increment or decrement the digit.

Up – Increments the time delay.

Down – Decrements the time delay.

Save – Stores the time delay for use with inactivity disconnects.

Table C-7.

User Interface Configuration Options (10 of 10)

«
...
169
170
171
172
173
...
»

Содержание 3160-A3











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3160-A3

EtherLink 3C509B

Бренд: 3Com Страницы: 8

Бренд: 3Com Страницы: 8

DR-4100P Series

Бренд: Idis Страницы: 30

Module NI PXI-8250

Бренд: National Instruments Страницы: 39

Бренд: Patton electronics Страницы: 75

RocketLink-G 3088/I

Бренд: Patton electronics Страницы: 61

Бренд: Patton Страницы: 12

Бренд: Patton Страницы: 84

OnSite 3210 Series

Бренд: Patton Страницы: 110

Бренд: Patton electronics Страницы: 2

SMARTNODE 4110 Series

Бренд: Patton electronics Страницы: 78

Бренд: Patton electronics Страницы: 8

Бренд: Salusfin Страницы: 6

Бренд: Amperes Страницы: 8

Бренд: Lanner Страницы: 109

ACC-CX3RDK-CU5640

Бренд: e-con Systems Страницы: 9

Бренд: Davey Страницы: 18

PCH1 T P Series

Бренд: Parker Страницы: 107

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды