Paradyne 3160-A3 Скачать руководство пользователя

Страница: 140 / 298

4. Maintenance

4-38

February 2001

3160-A2-GB21-90

Table 4-10. Test Status Message

Message

Description

No Test Active

No tests are currently active.

LLB Test Active

The network interface is in Line loopback.

PLB Test Active

The network interface is in Payload loopback.

DLB Test Active

The DTE Drop/Insert (DSX-1) port is in DTE loopback.

RLB Test Active

The DTE Drop/Insert (DSX-1) port is in Repeater loopback.

DCLB on Port

Port

n is in a Data Channel loopback.

DTLB on Port

Port

n is in a Data Terminal loopback.

QRSS on Net

A QRSS test pattern is being sent on the network interface.

1–8 Test Active

A 1-in-8 test pattern is being sent on the network interface.

QRSS on Port

A QRSS test pattern is being sent to the network on the channels
allocated to port

511 on Port

A 511 test pattern is being sent to the network on the channels
allocated to port

Mon QRSS, Net

A QRSS test pattern is being monitored on the network interface.

Mon QRSS, Port

A QRSS test pattern is being monitored on the channels
allocated to port

Mon 511, Port

A 511 test pattern is being monitored on the channels allocated to
port

DLB Test, Extrn

The DTE Drop/Insert (DSX-1) port is being held in DTE loopback
by the external contact.

Lamp Test Active

The Lamp test is currently active.

Содержание 3160-A3











































































































































































































































































































Результаты поиска

Содержание 3160-A3

Отзывы:

Похожие инструкции для 3160-A3

Бренды по названию

Популярные бренды

Paradyne 3160-A3, Руководство оператора

Результаты поиска

Содержание 3160-A3

Отзывы:

Похожие инструкции для 3160-A3

Бренды по названию

Популярные бренды