Paradyne 3160-A3 Скачать руководство пользователя

Страница: 254 / 298

G. Front Panel Emulation

G-2

February 2001

3160-A2-GB21-90

Procedure

To install Front Panel Emulation software:

1. Insert the diskette into the appropriate drive.

2. Select File from Program Manager.

3. Choose Run.

4. Type A:INSTALL and click OK.

5. An Information screen appears. Choose Continue to continue the installation.

6. Type the letter of the destination drive, followed by a colon (default is C:), then

the appropriate directory name (default is C:\FRONTPAN).

If the selected directory already exists, the following message appears:

The

specified directory already exists. Do you want to
overwrite the directory?

If the selected directory is new, the following message appears:

The

specified directory does not exist. Do you want to create
the directory?

7. Select Yes. A confirmation screen appears. Select Install to continue the

installation.

8. A Setup Completed screen appears. Select Continue. The Program Manager

screen appears with the Front Panel icon.

Содержание 3160-A3











































































































































































































































































































Результаты поиска

Содержание 3160-A3

Отзывы:

Похожие инструкции для 3160-A3

Бренды по названию

Популярные бренды

Paradyne 3160-A3, Руководство оператора

Результаты поиска

Содержание 3160-A3

Отзывы:

Похожие инструкции для 3160-A3

Бренды по названию

Популярные бренды