Paradyne 3160-A3 Скачать руководство пользователя | Manualshive

Страница: 221 / 298

background image

E. SNMP MIB Objects

3160-A2-GB21-90

February 2001

E-7

Interface Group – “ifSpeed” Object (ifEntry 5)

This object provides the interface’s current bandwidth in bits per second. The
value of this object for each interface is specified as follows:

Interface Group – “ifAdminStatus” Object (ifEntry 7)

This object specifies the desired state (configuration) of the interface. This object
is supported only for the COM and MODEM ports. It provides the ability to switch
between using the port for SNMP or ASCII operations (dial-out, front panel
emulation). The value of this object will not affect the state of any of the interfaces
on the DSU/CSU other than the COM or MODEM port. Only the following values
are supported by the DSU/CSU:

up(1) – The SNMP management link is active on the COM or MODEM port.

testing(3) – The SNMP management link is inactive on the COM or MODEM
port. These ports can be used for proprietary ASCII functions.

T1 Interfaces:

1,544,000 bps.

COM, AUX, and
MODEM:

The currently configured data rate for the port.

Data Ports:

The currently configured data rate for the port when the port
is allocated to one of the T1 interfaces. If the port is not
allocated the data rate is defined as zero.

«
...
219
220
221
222
223
...
»

Содержание 3160-A3











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3160-A3

TokenLink Velocity 3C319

Бренд: 3Com Страницы: 2

Бренд: 4IPNET Страницы: 97

Бренд: Quantum Страницы: 20

Brocade X6-8 Director

Бренд: Broadcom Страницы: 207

Бренд: Juniper Страницы: 190

PARTNER Voice Messaging PC Card Release 2

Бренд: Lucent Technologies Страницы: 67

Бренд: Ravpower Страницы: 27

Бренд: Rane Страницы: 128

Бренд: Acard Страницы: 34

Бренд: Shure Страницы: 113

ipRocketLink IAD 3086

Бренд: Patton electronics Страницы: 12

Бренд: Altera Страницы: 33

Бренд: Softing Страницы: 16

Бренд: ETAS Страницы: 84

Powereta iQP Series

Бренд: TDK Страницы: 2

TeleMyo 2400T V2

Бренд: Noraxon Страницы: 52

RoteFinder RF500S

Бренд: Multi-Tech Страницы: 134

Бренд: ST Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды