Paradyne 3160-A3 Скачать руководство пользователя | Manualshive

Страница: 185 / 298

background image

C. Configuration Options

3160-A2-GB21-90

February 2001

C-41

Trap I/F: All
Next NET DTE T1s Ports All Prev

Link Trap Interfaces. Specifies which interfaces generate linkUp and linkDown trap
messages. These traps are supported on the T1 interfaces (network and DTE
Drop/Insert) and the synchronous data ports.

NET – Sends trap messages for linkUp and linkDown events occurring on the network
interface.

DTE – Sends trap messages for linkUp and linkDown events occurring on the DTE
Drop/Insert (DSX-1) interface. This selection does not appear if the DTE Drop/Insert
(DSX-1) interface is disabled.

T1s – Sends trap messages for linkUp and linkDown events occurring on the network or
DTE Drop/Insert (DSX-1) interface.

Ports – Sends trap messages for linkUp and linkDown events occurring on the
synchronous data ports.

All – Sends trap messages for linkUp and linkDown events occurring on the network
interface, DTE Drop/Insert (DSX-1) interface, or the synchronous data ports.

NOTE: This configuration option is not available if the Link Trap configuration option is
not configured to generate trap messages for linkUp or linkDown events.

Table C-10. Management Trap Configuration Options (3 of 3)

«
...
183
184
185
186
187
...
»

Содержание 3160-A3











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3160-A3

Бренд: VAF instruments Страницы: 56

Бренд: Tripp Lite Страницы: 20

Бренд: Draytek Страницы: 8

HomePlug AV Ethernet Bridge PLE0200

Бренд: Abocom Страницы: 2

Бренд: N.A.T. Страницы: 32

Бренд: IDT Страницы: 93

Бренд: National Instruments Страницы: 130

Бренд: Kohler Страницы: 32

Бренд: HighPoint Страницы: 10

GSM7224v2 - Layer 2 Managed Gigabit Switch

Бренд: NETGEAR Страницы: 3

Industrial Network Track OSI

Бренд: GarrettCom Страницы: 10

2410SA - Serial ATA RAID Controller

Бренд: Adaptec Страницы: 14

E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor

Бренд: Intel Страницы: 112

Бренд: Vega Страницы: 12

Ether-GSH24T v3

Бренд: AirLive Страницы: 2

Бренд: Raven Страницы: 33

Бренд: Abocom Страницы: 70

Бренд: Sennheiser Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды