Paradyne 3160-A3 Скачать руководство пользователя | Manualshive

Страница: 55 / 298

background image

3. Operation

3160-A2-GB21-90

February 2001

3-21

Setting the IP Address

The IP address is the address used by the SNMP or Telnet system to access the
DSU/CSU (see

Appendix F,

IP Network Addressing Scenarios

). For DSU/CSUs

using PPP, the IP address can be negotiated if the network device (e.g., router or
SNMP manager) supports such negotiation. The IP address is composed of four
fields with three digits per field (

xxx.xxx.xxx.xxx

).

The IP address is set for the MODEM port, the COM port, or the AUX port (with
LAN Adapter or daisy chain), depending on which one has been chosen as the
SNMP or Telnet communication link. The example below assumes that an IP
address of 010.155.111.222 is being set for the COM port. You can use the same
principles to assign any value (between 000 and 255 for each digit field) to other
ports.

Procedure

To assign an IP address to the COM port:

1. From the top-level menu screen, select Cnfig.

2. Select the configuration option set to be copied into the Edit area by using the

appropriate Function key. Use the scroll keys, if necessary.

3. Select Edit.

4. From the Edit screen, press the

key until the Mgmt selection appears on

the screen.

5. Select Mgmt.

6. From the Mgmt Config screen, select Gen.

7. Press F1 (Next) until the Com IP Adr configuration option appears.

NOTE:

Steps 8 and 9 describe the process for entering an IP address. This
process applies to any IP address.

F1

F2

F3

Edit:
User Alarm Mgmt

F1

F2

F3

Mgmt Config:
Gen Trap

«
...
53
54
55
56
57
...
»

Содержание 3160-A3











































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3160-A3

Бренд: 3Com Страницы: 8

8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink

Бренд: Tyco Electronics Страницы: 18

Бренд: Lattice Semiconductor Страницы: 15

iCE40 UltraLite

Бренд: Lattice Semiconductor Страницы: 13

Wireless Mini PCI Module

Бренд: E-Tech Страницы: 42

Бренд: Dantel Страницы: 62

Бренд: Softing Страницы: 4

Бренд: Aethra Страницы: 2

Бренд: SeaLevel Страницы: 21

Бренд: VCS Страницы: 118

Бренд: Observint Страницы: 117

Бренд: Supermicro Страницы: 15

E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor

Бренд: Intel Страницы: 112

IP-Logic ZIG-IPPRO-RX

Бренд: Zigen Страницы: 4

Бренд: Teldat Страницы: 23

Бренд: Ubiquiti Страницы: 20

Бренд: Cypress Semiconductor Страницы: 31

Бренд: netsys Страницы: 164

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды