Panasonic AJ-PX380G, Руководство по эксплуатации

Страница: 215 / 229

– 215 –
Chapter 11 Maintenance — Warning system
Display Description Behavior and cause
[PROXY ERROR] An error occurred in the internal proxy module.
f The current operation will continue.
f Turn off the camera and turn on it again to check the
recording and playback. If the error continues to occur,
please consult your dealer.
[PROXY REC WARNING] A proxy data recording error occurred.
f The current operation will continue.
f Turn off the camera and turn on it again to check the
recording and playback. If the error continues to occur,
please consult your dealer.
[REC IMPOSSIBLE] (slot number)
An SDHC/SDXC memory card is inserted into the P2
memory card slot.
Recording to the SDHC/SDXC memory card is disabled.
f The current operation will continue.
f Record to microP2 or P2 memory cards.
[REC WARNING]
[FRAME SIGNAL]
Displayed when a video or audio error occurs during
recording.
f Tally lamp flashes four times per second during
continuous recording.
f The current operation will continue. When input
signals are disrupted, recording continues while
disrupted images are recorded. Check the signal to be
input to the camera.
f Turn off the power and on before using it again.
[REC WARNING]
[OVER MAX# CLIPS]
Displayed when attempting to record in excess of the
maximum total number of clips allowed for one P2 card.
f The tally lamp and <WARNING> lamp flash four times
per second during continuous recording.
f The operation will stop.
f Replace the P2 card or delete unnecessary clips.
Displayed after approximately 3.5 hours has elapsed
from the time when operation to start a single recording
is executed when [SHORT SPLIT] is selected in the
main menu → [RECORDING SETUP] → [FILE SPLIT].
f The operation will stop.
[REC WARNING]
[PULL DOWN]
(Occurs during recording)
The video pull-down sequence and time code values
are not synchronized.
f Tally lamp flashes four times per second during
continuous recording.
f The current operation will continue.
f Check the signal.
[REC WARNING]
[PULL DOWN ERROR]
(Occurs at times other than during recording)
The video pull-down sequence and time code values
are not synchronized.
f The current operation will continue.
f Check the signal.
[REC WARNING]
[REC DATA]
Displayed when an error occurs in recorded data during
recording.
f The tally lamp and <WARNING> lamp flash four times
per second during continuous recording.
f The operation will continue or stop.
f Turn off the power and on before using it again.
[RUNDOWN CARD] (slot number)
The maximum number of overwrites has been
exceeded.
f The current operation will continue.
f Replacement of the P2 card is recommended.
[SD CARD] (slot number)
An SDHC/SDXC memory card is inserted into the
microP2 memory card slot.
f The current operation will continue.
f Use of microP2 or P2 memory card is recommended.
[SLOT3 CANNOT REC]
[microP2 SELECTED]
Displayed when the card is inserted into the slot which
is not selected as the recording slot.
f The operation stops.
f Set the main menu → [RECORDING SETUP] → [REC
MEDIA] to [P2].
[SLOT3/4 CANNOT REC]
[P2 SELECTED]
Displayed when the card is inserted into the slot which
is not selected as the recording slot.
f The operation stops.
f Set the main menu → [RECORDING SETUP] → [REC
MEDIA] to [microP2].
[CHECK SLOT] (slot number)
The memory card may not be recognized correctly due
to reasons such as the P2 card being inserted slowly or
the terminal of the memory card may be dirty.
f The current operation will continue.
Recording cannot be performed on the inserted P2
card.
f Check the P2 card that is inserted.
[TEMPORARY PAUSE]
[IRREGULAR SIG]
Correct recording is not possible due to disruption
of input signals of the <GL IN/VIDEO OUT> or <SDI
OUT2/IN> terminal, etc., and recording is suspended
temporarily. The clip will be divided.
f Tally lamp flashes four times per second during
continuous recording.
f The operation will pause.
f Recording resumes when the signal returns to normal.
However, during loop recording, recording does not
resume.
[WIRELESS-RF]
Audio wireless reception status is poor.
f The tally lamp flashes four times per second during
continuous recording.
f The <WARNING> lamp flashes four times per second
during continuous recording and recording standby.
f The current operation will continue.
[UP LIST #99/100]
The number of registrations in the upload list of the rec
during upload function has reached 99.
f The current operation will continue.
One more clip to the upload list can be registered.
Delete unnecessary clips in the upload list.
[UP LIST #100/100]
The number of registrations in the upload list of the rec
during upload function has reached the upper limit.
f The current operation will continue.
When more additional clips need to be registered,
delete unnecessary clips in the upload list.
[UP LIST OVER MAX #]
Clips cannot be added for registration because the
number of registrations in the upload list of the rec
during upload function has reached the upper limit.
f The current operation will continue.
When additional clips need to be registered, delete
unnecessary clips in the upload list.