Panasonic AJ-PX380G, Руководство по эксплуатации

Страница: 102 / 229

– 102 –
Chapter 4 Shooting — Setting the time data
- [ − ]: The value of the digit to be set is incremented by one.
- [RST]: The value of the digit to be set is decremented by one.
5
Press the < % /REW> button, enter the values of user bits, and exit the user bits settings screen.
6
Select [USER] in the main menu → [RECORDING SETUP] → [UBG MODE].
@ @
NOTE
t If you exit the user bits setting screen without pressing the < % /REW> button, the set values are disabled.
Retention of user bits in memory
User bit settings are automatically recorded and are retained even if the power is turned off.
Frame rate information recorded on user bits
Saving the frame rate values for the image information shot/saved according to the frame rate set in the main menu → [SYSTEM MODE] to user bits
allows you to use the editor (personal computer editing software).
Information is always saved in VITC UB.
In addition, selecting [FRAME RATE] in the main menu
→ [RECORDING SETUP] → [UBG MODE] saves the information also in user bits (LTC UB). In
playback of clips recorded in native format, the same values as the frame rate information obtained by playing back recorded user bits are also output
as HD SDI output signals or user bits of TC output from the <TC IN/OUT> terminal.
Frame rate information
The relationship between frame rates, image pull-down, and time codes/user bits is as follows.
・ 60i ： 600
・ 60P ： 608
・ 30P ： 308
・ 24P ： 248
・ 24PN ： 24C
・ 50i ： 502
・ 50P ： 50A
・ 25P ： 25A
・ ＊＊ P ：＊＊ 9
・ ＊＊ P ：＊＊ 1
・ ＊＊
P
：＊＊
D
・ ＊＊
P
：＊＊
B
・
・
Verification information on the right-hand six digits
Fixed values
Sequence No.
24P: 0 - 4
Other than the above: Fixed to F
Media management information
Updated frame flags and valid frame flags
REC mark
Camera image mode
Example)
(During shooting)
(VFR 30PN or over 60P)
(VFR over 60P)
(VFR 24PN during shooting)
(VFR 25PN or over 50P)
Setting the time code
1
Set [DF] or [NDF] in the main menu → [RECORDING SETUP] → [DF MODE].
f Set [DF] to advance the time code in the drop frame mode, and set [NDF] to advance it in the non-drop frame mode. However, note that the time
code runs by [NDF] at all times in the 24PN mode.
2
Press the <SETUP> button to display the [SET01:TC/UB] screen of SmartUI.
3
Press the <COUNTER> button to set the counter display to [UB].
4
Press the < % /REW> button to set [TCG] to [SET].
5
Set the time code.
f Press the upper or lower buttons that correspond to the following screen displays.
- [
→ ]: The digit to be set (flashing) moves to the right.
- [ + ]: The digit to be set (flashing) moves to the left.
- [ − ]: The value of the digit to be set (flashing) is incremented by one.
- [RST]: The value of the digit to be set (flashing) is decremented by one.
6
Press the < % /REW> button, enter the setting values of the time code, and exit the time code settings screen.
7
Press the <HOME> button to display the [HOME] screen of SmartUI.