Panasonic AJ-PX380G, Руководство по эксплуатации

Страница: 214 / 229

– 214 –
Chapter 11 Maintenance — Warning system
Warning system
If an error is detected immediately after the camera is turned on or during operation, the viewfinder, <WARNING> lamp, and tally lamp indicate the error.
Deal with the error by following the indications.
Cases indicated by error codes
Error code Display Description Behavior and cause
[E-30]
[TURN POWER OFF]
[P2 CARD]
An error occurred in the camera built-in memory
because the P2 card being accessed was ejected.
f Tally lamp flashes four times per second.
f <WARNING> lamp flashes four times per second.
f Cannot operate.
f Follow the message to turn off the power once and
turn on the power again.
f Ensure that there is no error in the clips on the ejected
card, and restore the clips as necessary.
[E-31]
[TURN POWER OFF]
[SYSTEM MODE]
System mode error occurred.
f Tally lamp flashes four times per second.
f <WARNING> lamp flashes four times per second.
f Cannot operate.
f Follow the message to turn off the power once, turn
on the power again, and check that there is no error
display.
[E-33]
[SYSTEM ERROR]
[CAMERA]
Camera unit error occurred.
f Tally lamp flashes four times per second.
f <WARNING> lamp flashes four times per second.
f
The operation stops.
f Contact your dealer.
[E-35]
[SYSTEM ERROR]
[CODEC]
Codec control error occurred.
f Tally lamp flashes four times per second.
f <WARNING> lamp flashes four times per second.
f The operation stops.
f Contact your dealer.
[E-36]
[SYSTEM ERROR]
[P2 SYSTEM]
P2 system error occurred.
f Tally lamp flashes four times per second.
f <WARNING> lamp flashes four times per second.
f The operation stops.
f Contact your dealer.
[E-37]
[SYSTEM ERROR]
[P2CS]
P2CS microcomputer error occurred.
f Tally lamp flashes four times per second.
f <WARNING> lamp flashes four times per second.
f The operation stops.
f Contact your dealer.
[E-39]
[SYSTEM ERROR]
[INITIALIZE]
Video initialization error occurred.
f Tally lamp flashes four times per second.
f <WARNING> lamp flashes four times per second.
f The operation stops.
f Contact your dealer.
[E-63] No display
System control microcomputer error occurred.
f Tally lamp flashes four times per second.
f <WARNING> lamp flashes four times per second.
f The operation stops.
f Contact your dealer.
[E-64]
[SYSTEM ERROR]
[FRAME SIGNAL]
(or no display)
Reference signal error occurred.
f Tally lamp flashes four times per second.
f <WARNING> lamp flashes four times per second.
f The operation stops.
f Contact your dealer.
Cases indicated by error messages
During recording/playback
Display Description Behavior and cause
[AUTH NG CARD] (slot number)
CPS authentication of microP2 memory card has failed.
The microP2 memory card whose CPS authentication
failed cannot be recorded or played back.
f The current operation will continue.
f Select [AUTHENTICATE] in the main menu → [CLIP],
and enter the password.
[BACKUP BATT EMPTY]
Displays any reduced voltage detected on the backup
battery in the internal clock when the power is turned
on.
f The current operation will continue.
f Charge the built-in battery.
[CARD ERROR] (slot number)
Displayed when an data error caused by the P2 card
occurs during recording.
Displayed after recording stops until the next operation.
Also displayed for three seconds during playback when
a P2 card error causes playback to stop.
f If the error occurs during recording, the tally lamp and
<WARNING> lamp flash four times per second for
approx. three seconds after recording stops.
f The tally lamp does not flash when an error occurs
during playback.
f The operation will stop.
f After it stops, the P2 card on which the error occurred
is write-protected. Replace the P2 card of the slot
where the error occurred.
[CLIP DISCONTINUED]
Displayed when clips cannot be linked with the
subsequent recording operations due to the
inconsistency as linked clips during recording in one-clip
recording mode.
f The current operation will continue.
[DIR NG CARD] (slot number) The directory position is not correct.
f The current operation will continue.
f Make a card backup immediately and format the card
to use it again.
[PB INTERMITTENT]
Playback is interrupted on the SDHC/SDXC memory
card. A card whose playback performance cannot be
assured is inserted.
f The current operation will continue.
f Use of microP2 or P2 memory card is recommended.