Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 13 / 76

IG-308-EN version 01; 03/06/2022

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

Handling and transport

Lifting using slings or chains fixed to the lifting brackets

on the sides of the top of the cubicle. The angle of pull

should be as vertical as possible (with an angle greater

than 60º from the horizontal).

Figure 2.2.

Lifting a

cgm

.3-huv-l

modular cubicle with chains.

Figure 2.3.

Lifting a

cgm

.3-huv-lv

compact cubicle with chains.

If it is not possible to use the aforementioned methods,

rollers may be used underneath the switchgear. Another

option is to slide the cubicles over rods (these same

rods can be used to help get over the cable trench).

Once the corresponding operations have been

completed, remove the two lifting angles from the

cubicle unscrewing the three M8 screws of each lifting

angle.

Figure 2.4.

Removing the lifting angles

With the lifting angles of the

cgm

.3.huv-lv or

cgm

.3-rbv,

an additional functional unit can be lifted.

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды