Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 68 / 76

IG-308-EN version 01; 03/06/2022

Maintenance

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

7. Maintenance

For safety reasons, maintenance operations performed

directly on the driving mechanism must be performed

WITHOUT any actuating levers inserted.

The live parts of the main circuit and switching equipment

do not require inspection or maintenance, as they are

completely insulated in SF

, and therefore free from any

influence from the external environment.

The operating mechanism for the

cgm

.3-huv system

cubicles' driving units does not require lubrication for

correct operation throughout its estimated lifetime,

according to the service conditions specified in IEC 62271-1.

These mechanisms must be inspected when used under

extreme conditions (dust, salt, pollution). It is advisable to

carry out at least one operation during the inspections.

Components manufactured from galvanised sheet steel

have been painted to ensure their resistance to corrosion.

Any scratches, dents or similar on them must be repaired to

prevent corrosion.

Facilities which operate under severe climate

conditions, in excess of those defined as normal

service conditions (IEC 62271-1), must carry out the

regular preventive maintenance tasks required. Check

with

Ormazabal

for the environmental conditions of

the facility.

7.1. Voltage presence indicating relay test

To test the

ekor

.vpis or

ekor

.ivds voltage presence

indicating relay, connect it to a 230 V

power supply. To

do this, disconnect the

ekor

.vpis or

ekor

.ivds device from

the cubicle, and, using 4 mm cable connectors, apply the

voltage between the test point for the phase to be checked

and the earth test point.

No polarity is defined for 230 V

, so either the phase or

neutral conductor can be connected.

If a flashing signal is observed, the device is working

correctly. In order to properly test the

ekor

.vpis or

ekor

.ivds, this check should be carried in the three phases.

Voltage presence indication is not sufficient in itself to

ensure that the facility has been disconnected from

the electricity supply. It is necessary to confirm that

the feeder is connected to earth before accessing the

cable compartments.

The

ekor

.vpis or

ekor

.ivds voltage indicator can be replaced

if necessary. To do so, loosen to release the two screws on

the top right and bottom left of the indicating relay using a

medium-size Phillips screwdriver. The

ekor

.vpis or

ekor

.ivds

unit can then be disconnected from base without needing

to power down the feeder.

Figure 7.1.

Connection mode

ekor

.vpis

ekor

.ivds

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды