Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 7 / 76

IG-308-EN version 01; 03/06/2022

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

General description

1.3.3. Base

Made up of the cable compartment and the gas relief

compartment:

Cable compartment

This is located in the bottom front section of the cubicle

and has a cover interlocked with the earthing switch, thus

allowing front access to the medium-voltage cables.

standard

, it is designed to contain up to:

• Two shielded screw-in cable connectors (reduced) per

phase or one cable connector (reduced) plus surge

arrester (reduced) with space for the corresponding

incoming power cables.

• Cable ties for the power cables.
• Earthing bars.

As an

option

• Two symmetric cable connectors or symmetric cable

connector plus symmetric surge arrester.

Figure 1.3.

Cable compartment

Gas relief compartment

Ormazabal

cgm

.3-huv system is designed and

constructed to withstand at least the thermal and dynamic

effects of an arc of 25 kA for 1 second should a defect result

in an internal arc in the gas compartment. The system

conducts the gases generated in a fully controlled manner

to avoid any possible injury to people in the equipment

operation area.

Optionally

, a relief duct can be fitted in the rear of the

cubicle to redirect the gases to the top. Please check

with

Ormazabal

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды