Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 14 / 76

IG-308-EN version 01; 03/06/2022

Storage

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

3. Storage

If it needs to be stored, the equipment must be placed on

dry ground or on top of damp-proof insulating material, still

in its original packing.

After prolonged storage, clean all the insulating parts

carefully before commissioning the equipment. The

enclosure should be cleaned with a clean, dry lint-free cloth.

Figure 3.1.

Storage conditions

Storage must always be INDOORS, with the following

conditions recommended:

Ambient air temperature should not exceed 40 ºC

and its mean value, measured in a period of 24 hours,

should not exceed 35 ºC.

The ambient air temperature must not drop below

- 5 °C. There are also cubicles with storage temperature

up to - 40 °C.

The switchgear must be protected from direct solar

radiation.

Altitude, both in transport and in storage, must not

exceed 2000 m.

The environmental air must not have any significant

contamination from dust, smoke, corrosive and/or

inflammable gases, vapours or salt.

The switchgear must be protected from the rain, and

the humidity conditions must be as follows:

the average relative humidity value, measured over

a period of 24 hours, must not exceed 95 %.

the average water vapour pressure value, measured

over a period of 24 hours, must not exceed 2.2 kPa.

the average relative humidity value, measured over

a period of one month, must not exceed 90 %.

the average water vapour pressure value, measured

over a period of one month, must not exceed

1.8 kPa.

During transport, vibrations caused by external factors

or seismic movements must be insignificant.

Any other conditions must be notified beforehand,

since the equipment must be factory-adjusted to

atmospheric pressure at the destination.
If this is not the case, the pressure gauge needle may

indicate an incorrect value, even if the equipment's

internal pressure is correct.

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды