Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 17 / 76

IG-308-EN version 01; 03/06/2022

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

Installation

4.3. Minimum installation distances

[5]

For any questions, please ask

Ormazabal

[6]

In each case, bear in mind which cable is to be used in the particular installation.

The minimum distances to the walls and roof which must

be maintained in the facility are as follows:

Figure 4.2.

Minimum installation distances

Minimum distances [mm]

Side wall (a)

100

Roof (b)

1050

Front clearance (c)

500*

Function

Rear wall (d)**

-l/-v/-rc/-ma/-lv/-rbv

100

* An operating clearance of 1000 mm is recommended.
** 800 in the case of AFLR

Table 4.1.

Minimum distances

The measurements indicated in the table have been

obtained in accordance with the dimensions of the

test room for the gas-filled modules, according to

Annex A of Standard IEC 62271-200.

The space required to extend the assembly with an

additional cubicle is 250 mm plus the width of the new

cubicle

[5]

4.4. Recommended cable connection trenches

Minimum recommended dimensions based on the trench

dimensions used in the tests in accordance with Standard

IEC 62271-200. These dimensions may vary in accordance

with the radius of curvature of the cables used

[6]

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды