Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 44 / 76

IG-308-EN version 01; 03/06/2022

Recommended sequence of operations

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

3. Switch-disconnector closing operation:

a. Manual operation

Insert the lever in the switch-disconnector actuating

shaft, move the actuating arm to the end and turn

clockwise.

b. Motorised operation

(BM driving mechanisms).

Activate the corresponding operation command.

Figure 5.26.

Lever turn detail

Remove the lever. The handle returns to its original

position.

For manual driving mechanisms, charge the springs

by introducing the spring charging lever in the spring

charge shaft (k) and turn until the charged spring

indicating relay changes status.

For motorised driving mechanisms (AMV):

Close the

circuit-breaker by pressing the close button.

Close the circuit-breaker by pressing the "l" button and

check the status indicating relay.

Figure 5.27.

Closing button detail

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды