Ormazabal velatia cgm.3 system Скачать руководство пользователя

Страница: 65 / 76

IG-308-EN version 01; 03/06/2022

General instructions

cgm

.3-huv system: Fully gas-insulated

medium-voltage switchgear

Safety elements

6. Safety elements

6.1. Acoustic earthing prevention alarm

[14]

Incompatible with use of

ekor

.ivds

units

The

ekor

.sas acoustic alarm unit is associated to the

ekor

.vpis voltage presence indicating relay and to the earth

shaft actuator. The alarm is activated when there is voltage

in the functional unit's medium-voltage feeder and the

lever is inserted in the earthing switch shaft. A sound then

indicates that a short-circuit or zero voltage may occur in

the network if the operation is carried out.

Operation of the unit is assured within the same operating

range as the

ekor

.vpis unit associated with it

[14]

Audible alarm

ekor

.sas for line position.

Figure 6.1. ekor

.sas unit

6.2. Interlocks

The switchgear is provided with interlocks, which ensure

the following conditions:

The switch-disconnector and the earthing switch

cannot both be in closed position at the same time.

The cubicles have an interlock which prevents access

to the medium-voltage cable compartment whenever

the earthing switch is not closed. In normal operation,

this earthing switch cannot be opened if the cable

compartment cover is not in place.

Содержание velatia cgm.3 system













































































Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды

Ormazabal velatia cgm.3 system, Общее руководство по инструкции

Результаты поиска

Содержание velatia cgm.3 system

Отзывы:

Похожие инструкции для velatia cgm.3 system

Бренды по названию

Популярные бренды