![background image](http://html1.mh-extra.com/html/omron/sysdrive-3g3fv/sysdrive-3g3fv_user-manual_743234271.webp)
6-97
•
The multi-function outputs can be set to monitor any of the U1 Inverter status items by setting the last
two digits of the parameter number (U1-
).
Refer to page 3-12 for a table listing all of these U1 settings.
•
The Inverter’s status monitor item U1 can be output as multi-function analog output. Set the parame-
ters H4-01 and H4-03 (AO Ch1 Select and AO Ch2 Select) to the right side of the of “U1” constants in
the table on page 3-12 of this manual. The setting range is between 1 and 38, but the following num-
bers cannot be set: 4, 10, 11, 13, 14, 25, 28, 29, 30, 31, 34, 35.
D
Adjusting the Monitor Output
Parameter
Display name
Setting
Units
Default
Valid access levels
number
p y
g
range
setting
V/f
Control
V/f with
PG
Open Loop
Vector
Flux
Vector
H4-02
Terminal 21 Gain
0.00 to 2.50
Factor
1.00
Basic or Advanced
H4-03
Terminal 21 Bias
–10.0 to 10.0 %
0.0
Basic or Advanced
H4-05
Terminal 23 Gain
0.00 to 2.50
Factor
0.50
Basic or Advanced
H4-06
Terminal 23 Bias
–10.0 to 10.0 %
0.0
Basic or Advanced
Note These parameters can be changed during operation.
•
For the output gain, set what multiple of 10 V will correspond to a 100% output of the monitored item.
•
For the output bias, set the amount that the output characteristic will be shifted vertically.
Set this amount as a percentage, with 10 V corresponding to 100%.
Output voltage
Gain
×
10 V
Bias
10
100
V
Monitored item
0%
0 V
100%
10 V
D
Multi-function Analog Output Signal Level
Parameter
Display name
Setting
Units
Default
Valid access levels
number
p y
g
range
setting
V/f
Control
V/f with
PG
Open Loop
Vector
Flux
Vector
H4-07
AO Level Select
0 or 1
---
0
Basic or Advanced
Note This parameter cannot be changed during operation.
Setting
Function
0
0 to +10 V (Absolute value output)
1
0 to
±
10 V
•
This signal level setting applies to analog outputs 1 and 2 (terminals 21 and 23).
•
When the 0- to
±
10-V signal level is used to output speed values (frequency reference, output frequen-
cy, or motor speed), positive voltage indicates Inverter output in the forward direction and negative
voltage indicates Inverter output in the reverse direction. (Assuming a bias setting of 0.0.)
Advanced Operation
Chapter 6
Содержание SYSDRIVE 3G3FV
