![background image](http://html1.mh-extra.com/html/omron/sysdrive-3g3fv/sysdrive-3g3fv_user-manual_743234268.webp)
6-94
Setting
Control mode
Equivalent of 100% Input
(10 V or 20 mA)
Function
Setting
Flux
Vector
Open-loop
Vector
V/f
w/PG
V/f
Equivalent of 100% Input
(10 V or 20 mA)
Function
1F
Disable analog input (H3-05)
---
OK OK
OK
OK
Frequency Reference (H3-09)
Maximum frequency
Note 1. The analog inputs’ signal level, gain, and bias are set with the following parameters. Terminal
16 is the multi-function analog input and terminal 14 is the frequency reference (current) input.
Terminal 16 signal level selector
H3-04 (0 to +10 V or 0 to
±
10 V)
. . .
Terminal 16 input gain
H3-06
. . . . . . . . . . .
Terminal 16 input bias
H3-07
. . . . . . . . . . .
Terminal 14 signal level selector
H3-08 (0 to +10 V, 0 to
±
10 V, or 4 to 20 mA)
. . .
Terminal 14 input gain
H3-10
. . . . . . . . . . .
Terminal 14 input bias
H3-11
. . . . . . . . . . .
Note 2. When a voltage input is being input to terminal 14, be sure to disconnect jumper wire J1 on the
control board. The input resistance will be destroyed if a voltage input is used without discon-
necting the jumper wire.
Note 3. Set the time constant with the following parameter when adding a primary delay filter to an
analog input:
Analog input filter time constant
H3-12
. . .
This filter time constant applies to all three of the analog inputs.
Note 4. The frequency bias setting (setting: 2) is different from the frequency bias 2 setting (setting: D)
in the operation of the Inverter if the calculation results in a negative value. The frequency bias
will be limited to 0 and frequency bias 2 will rotate the motor in the reverse direction.
Note 5. The frequency bias and frequency bias 2 cannot be set together for two analog inputs. A set-
ting error (OPE07) will result if an attempt is made to set them.
D
Analog Input Characteristics with Gain = 100.0% and Bias = 0.0%
•
Auxiliary Frequency Reference (Setting: 0)
Frequency Bias (Setting: 2)
Frequency Bias 2 (Setting: D)
PID Feedback (Setting: B)
Frequency Reference (H3-09, Setting: 1F)
100%
–10 V
10 V
–100%
0
Advanced Operation
Chapter 6
Содержание SYSDRIVE 3G3FV
