Safety Instr
uctions
S-17
4.5.2 Automatic operation
Check the following points when operating the robot in AUTO mode. Observe the instructions below in cases where an
error occurs during automatic operation. Automatic operation described here includes all operations in AUTO mode.
1.
Checkpoints before starting automatic operation
Check the following points before starting automatic operation
DANGER
• CHECK THAT NO ONE IS WITHIN THE SAFETY ENCLOSURE.
• CHECK THE SAFETY ENCLOSURE IS SECURELY INSTALLED WITH INTERLOCKS FUNCTIONAL.
WARNING
• CHECK THAT THE PROGRAMMING BOX / HANDY TERMINAL AND TOOLS ARE IN THEIR SPECIFIED LOCATIONS.
• CHECK THAT THE SIGNAL TOWER LAMPS OR OTHER ALARM DISPLAYS INSTALLED FOR THE SYSTEM ARE NOT
LIT OR FLASHING, INDICATING NO ERROR IS OCCURRING ON THE ROBOT AND PERIPHERAL DEVICES.
2.
During automatic operation and when errors occur
After automatic operation starts, check the operation status and the signal tower to ensure that the robot is in automatic operation.
DANGER
NEVER ENTER THE SAFETY ENCLOSURE DURING AUTOMATIC OPERATION.
WARNING
IF AN ERROR OCCURS IN THE ROBOT OR PERIPHERAL EQUIPMENT, OBSERVE THE FOLLOWING PROCEDURE
BEFORE ENTERING THE SAFETY ENCLOSURE.
1) PRESS THE EMERGENCY STOP BUTTON TO SET THE ROBOT TO EMERGENCY STOP.
2) PLACE A SIGN ON THE START SWITCH, INDICATING THAT THE ROBOT IS BEING INSPECTED IN ORDER TO KEEP
OTHER PERSONS FROM RESTARTING THE ROBOT.
4.5.3 Precautions during operation
1.
When the robot is damaged or an abnormal condition occurs
WARNING
• IF UNUSUAL ODORS, NOISE OR SMOKE OCCUR DURING OPERATION, IMMEDIATELY TURN OFF POWER TO
PREVENT POSSIBLE ELECTRICAL SHOCK, FIRE OR BREAKDOWN. STOP USING THE ROBOT AND CONTACT YOUR
DISTRIBUTOR.
• IF ANY OF THE FOLLOWING DAMAGE OR ABNORMAL CONDITIONS OCCURS THE ROBOT, THEN CONTINUING TO
OPERATE THE ROBOT IS DANGEROUS. IMMEDIATELY STOP USING THE ROBOT AND CONTACT YOUR
DISTRIBUTOR.
Damage or abnormal condition
Type of danger
Damage to machine harness or robot cable
Electrical shock, robot malfunction
Damage to robot exterior
Damaged parts fly off during robot operation
Abnormal robot operation (position deviation, vibration, etc.)
Robot malfunction
Z-axis (vertical axis) or brake malfunction
Loads fall off
2.
High temperature hazard
WARNING
• DO NOT TOUCH THE ROBOT CONTROLLER AND ROBOT DURING OPERATION. THE ROBOT CONTROLLER AND
ROBOT BODY ARE VERY HOT DURING OPERATION, SO BURNS MAY OCCUR IF THESE SECTIONS ARE TOUCHED.
• THE MOTOR AND SPEED REDUCTION GEAR CASING ARE VERY HOT SHORTLY AFTER OPERATION, SO BURNS MAY
OCCUR IF THESE ARE TOUCHED. BEFORE TOUCHING THOSE PARTS FOR INSPECTIONS OR SERVICING, TURN OFF
THE CONTROLLER, WAIT FOR A WHILE AND CHECK THAT THEIR TEMPERATURE HAS COOLED.
Содержание R6YXGLC250
