Item
NX1P2-
11
££££
/
11
££££
1
10
££££
/
10
££££
1
90
££££
/
90
££££
1
9B
££££
/
9B
££££
1
Built-in
Ether-
CAT
port
Communications standard
IEC 61158 Type12
EtherCAT master specifications
Class B (Feature Pack Motion Control compliant)
Physical layer
100BASE-TX
Modulation
Baseband
Baud rate
100 Mbps (100BASE-TX)
Duplex mode
Auto
Topology
Line, daisy chain, branching and ring
Transmission media
Twisted-pair cable of category 5 or higher (double-shielded straight
cable with aluminum tape and braiding)
Maximum transmission distance be-
tween nodes
100 m
Maximum number of slaves
16
8
Range of node addresses that can be
set
1 to 192
Maximum process data size
Input: 1,434 bytes
Output: 1,434 bytes
Maximum process data size per slave
Input: 1,434 bytes
Output: 1,434 bytes
Communications cycle
2,000 μs to 8,000 μs in 250-μs increments
4,000 μs to
8,000 μs in
250-μs incre-
ments
Sync jitter
1 μs max.
Serial
Com-
munica-
tions
(Serial
Com-
munica-
tions
Option
Board)
Communications method
Half duplex
Synchronization method
Start-stop synchronization
Baud rate
1.2/2.4/4.8/9.6/19.2/38.4/57.6/115.2 kbps
Transmission distance
Depends on Option Board.
Supported protocol
Host link, Modbus-RTU master, and no-protocol
Unit
configu-
ration
Maximum
number of
connectable
Units
Maximum number of NX
Units that can be
mounted to the CPU
Unit
8
Maximum number of NX
Units for entire control-
ler
24
On CPU Rack: 8
On EtherCAT Slave Terminals: 16
Power sup-
ply
Model
A non-isolated power supply for DC input is built into the CPU Unit.
Power OFF detection
time
2 to 8 ms
Option
Board
Number of slots
2
2
1
Built-in
I/O
Input
Number of points
24
24
14
Output
Number of points
16
16
10
Load-short circuit pro-
tection
11
££
DT/10
££
DT/9024DT/9B
££
DT: Not provided(NPN)
11
££
DT1/10
££
DT1/9024DT1/9B
££
DT1: Provided(PNP)
1 Introduction to NX-series Controllers
1-12
NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)
Содержание NX1P2 series
