Omron NX1P2 series Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 264

background image

3-2

SD Memory Cards

This section describes the models, specifications, and application of the SD Memory Cards.

3-2-1

Models and Specifications

SD cards and SDHC cards are supported, but use one of the following OMRON Cards. OMRON is not
responsible for the operation, performance, or write life of any other SD or SDHC card.

Model

Card type

Capaci-

ty[GB]

Format

Number of over-

writes

Weight

HMC-SD291

SD Card

2 FAT16

2 g max.

HMC-SD491

SDHC Card

4 FAT32

HMC-SD1A1

16

*1.

This number represents the number of overwrites when the SD Memory Card is used on an NX-series CPU Unit. When
the SD Memory Card is used on other equipment such as a personal computer, the number of overwrites may be reduced.

*2.

This can be used for a CPU Unit with unit version 1.21 or later.

Additional Information

Write Protection Key
You will not be able to write to the SD Memory Card if the key is set to the LOCK position. Use
this setting to prevent overwriting.

3-2-2

Purpose

You can use the SD Memory Card for the following applications.
• Read and write files in the SD Memory Card with instructions.
• Read and write files in the SD Memory Card from an FTP client on EtherNet/IP.
• Back up, restore, and verify data in the Controller.
• Transfer data from the SD Memory Card to the Controller when the power is turned ON.

Refer to the

NJ/NX-series CPU Unit Software User’s Manual (Cat. No. W501)

for details on the func-

tions for SD Memory Cards.

3 Configuration Units

3-21

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

3-2
SD Memory Cards

3

3-2-1

Models and Specifications

«
...
101
102
103
104
105
...
»

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX1P2 series

Бренд: Zhone Страницы: 1

EK-FC780 GTX Jetstream

Бренд: ekwb Страницы: 2

Бренд: Pima Страницы: 4

Бренд: Intel Страницы: 108

DHI-NVR2104-P-4KS2

Бренд: Dahua Страницы: 23

Through Hole Power Inductors 1411

Бренд: Delta Electronics Страницы: 1

Бренд: Xtreme Страницы: 83

Бренд: Vacron Страницы: 16

Бренд: JAKA Страницы: 37

H8S/2646 Series

Бренд: Renesas Страницы: 20

Бренд: Xilinx Страницы: 27

Бренд: EZCast Pro Страницы: 4

Бренд: ekwb Страницы: 2

Бренд: Dave Embedded Systems Страницы: 79

Бренд: IBM Страницы: 74

Imagestore Intuition+

Бренд: Miranda Страницы: 60

Бренд: NEC Страницы: 47

H8S/2615 Series

Бренд: Renesas Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды